How to use Falcon 3.0 using Netware Lite with more than two systems.
   You need the WSGEN disk from Novell Netware 3.11 (Netware 2.11 may work
but I have not tested it) to create the file IPX.COM for your network card.
WSGEN will ask you the type network card you have and the selection of the 
I/O address, interrupt and memory address (this will be card dependent).
After youhave created the IPX.COM file, copy it and NETX.COM to your hard
drive.  If the WSGEN disk does not have the NETX.COM (for DOS Any DOS VER.)
file you can use NET4 or NET3.  Using Net3 (for DOS 3.X) or NET4
(for DOS 4.X) you must configure SETVER.EXE to report to the program that
the proper DOS version is being used.  After configuring SETVER you must
include it in your CONFIG.SYS file as a device driver when running Falcon.
   Only the system used as the Caller (Squadron Leader) needs to load these
files.  When loading the file NETX.COM it will seem to have locked up the
system, just wait it is looking for a dedicated server and should time out
after about 40 seconds with no server found (A dedicated SERVER IS NOT
REQUIRED!).  The Caller (Squadron Leader) system when in COMMS will receive
question marks (?) for the other Answer systems wanting to play, just select
each one and wait for them to respond then exit the selection menu.  When in
multi-player allied make sure to add enough planes for the number of systems
playing.  When using the multi-player allied mission the Squadron Leader must
pass each way point for the wingman way point to change.  I have used this
setup with six systems its awesome!!.
   We have found that the Israel Theater is unreliable in the network and
comm mode.  I don't know why but it will frequently hang resulting in all
systems to power down and start over.  Below is a list of the hardware and
configurations for the systems that I use.
If you have any question or input leave me a message or call me at:

Don Muddiman
407-892-4540 after 4pm EST

Also the Network and COMM created Squadrons Can be saved and added for
selection by Falcon.  The file names are SQUAD6.* there are 6 files.
Falcon will only bring up Squadron files 0-5 using the file names SQUAD0.*,
SQUAD1.*  etc.  (I think this was an over look by the programmers). If you know
how many squadrons you have created (so you don't over write them) you can add
the network or comm Squadrons.  All created and saved Falcon squadrons will
have 6 files with the names SQUAD?.CAM, SQUAD?.MIS, SQUAD?1.MTV, SQUAD?.ORG,
SQUAD?.SQU, SQUAD?.WAR (the ? mark indicates squadron number) you can add the
network or comm Squadrons to the Falcon Selection by renaming the SQUAD6.*
(Network or Comm) files to over write one of the existing squadrons 0-5 that
have only one squadron file name attached to it.  The added network/comm
squadron must be after the next squadron with 6 files attached to it.

Network Hardware and settings
LoneStar Arcnet 8 bit Bus Cards $59.00ea from Altex
Address CC00-CC7F (Excluded Address setting for Memory Manager)
Interrup 5
Memory I/O 02E0

Software
Falcon 3.0 Version C (Must be on all systems)
Novell Netware 3.11 WSGEN Disk
-------------------------------------------------------------------
Netware LiteFalcon Shell AUTOEXEC.BAT and CONFIG.SYS for Caller
(Squadron Leader)
Netware 3.11 files needed.
AUTOEXEC.BAT (Caller/Squadron Leader) 486-33 System
8Mb RAM, Sound Blaster, Pro, Mouse

prompt $p$g
path c:\;c:\dos;c:\mouse;c:\xt;c:\nwlite
LOADHIGH IPX
LOADHIGH NETX
LOADHIGH MOUSE
SET BLASTER=A220 I7 D1 T2
@SET SOUND=E:\FALCON3
SBP-SET /M:15 /VOC:15 /CD:15 /FM:15
mem
e:
cd\falcon3
PAUSE
FSHELL (Falcon Shell Program)

CONFIG.SYS (Caller/Squadron Leader)
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\SETVER.EXE
DOS=HIGH,UMB
DEVICE=C:\DOS\EMM386.EXE 5120 RAM FRAME=E000 X=CC00-CC7F
DEVICEHIGH=C:\DOS\SMARTDRV.SYS 2048 
DEVICEHIGH=C:\DOS\ANSI.SYS
BUFFERS=30
FILES=30
--------------------------------------------------------------------------
AUTOEXEC.BAT and CONFIG.SYS for Answer (Player) Netware Lite files needed.
AUTOEXEC.BAT (Player) 386-40 System, 8Mb RAM, Sound Blaster Pro, Mouse
prompt $p$g
path c:\;c:\dos;c:\mouse;c:\xt;c:\nwlite
LOADHIGH LSL
LOADHIGH TRXNET
LOADHIGH IPXODI A
LOADHIGH MOUSE
SET BLASTER=A220 I7 D1 T2
@SET SOUND=E:\FALCON3
SBP-SET /M:15 /VOC:15 /CD:15 /FM:15
mem
E:
cd\falcon3
FSHELL (Falcon Shell)


CONFIG.SYS (Player)
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\SETVER.EXE
DOS=HIGH,UMB
DEVICE=C:\DOS\EMM386.EXE 5120 RAM FRAME=E000 X=CC00-CC7F
DEVICEHIGH=C:\DOS\SMARTDRV.SYS 2048 
DEVICEHIGH=C:\DOS\ANSI.SYS
BUFFERS=30
FILES=30
--------------------------------------------------------------

Falcon Settings
Baud=19200
Connection=Network
Squadron Leader=Caller
Players=Answer