浜様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様� � � � Inboard 386/PC Technical Installation Instructions � � � 藩様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様� INSTALL THE INBOARD 386/PC (MOST SYSTEMS) Installing the Inboard 386/PC is a two-step process: 1. Putting the board into the computer 2. Copying and configuring the Inboard 386/PC software INSTALLING THE BOARD Before installing the Inboard 386/PC, verify that your computer is operating correctly. Fix any existing problems before adding the Inboard 386/PC. Once you know the computer is operating correctly, follow these steps to install the Inboard 386/PC. 1. Turn off the power switch on the computer and any attached equipment, and unplug the computer's power cord from the outlet. 2. Remove the computer's cover. 3. Remove any boards installed between the 8088 socket and the slot in which you're going to install the Inboard 386/PC. 4. Set the computer's system board switches to specify the appropriate amount of conventional memory. 5. Disable any conventional memory provided by add-in boards or remove the boards. 6. Remove the 8088 microprocessor. 7. If an 8087 is installed, remove it. 8. Align the Inboard 386/PC cable connector with pins over the 8088 socket (not the 8087 socket) so that pin 1 on the cable is at the notched end of the socket. Check for proper pin alignment before applying pressure. 9. Install the Inboard 386/PC into a full-length slot that is within reach of the cable. 10. Replace any boards you removed from the computer. 11. Route the Inboard 386/PC cable over (or, in some cases, under) other boards to the Inboard 386/PC. 12. Connect the free end of the cable to the Inboard 386/PC. 13. Replace the computer's cover, connect any cables you disconnected, and plug the power cord into the outlet. INSTALLING THE SOFTWARE Installing the Inboard 386/PC software is a two-step process: copying the software to the root directory and setting up the software (by adding commands to the CONFIG.SYS and AUTOEXEC.BAT files). If you can't find the Inboard 386/PC software, you can download the latest versions from the Intel Bulletin Board System or from Compuserve. COPYING THE INBOARD 386/PC SOFTWARE Before you can use the Inboard 386/PC software, you must copy it to your hard disk's root directory or your system diskette. Copy only the software you need. Here's a short description of the software: INBRDPC.SYS Controls extended memory and speed control keys. ISTATPC.EXE Displays the status of the INBRDPC.SYS settings. ICACHE.COM Controls the Inboard 386/PC's cache. ILIM386.SYS Turns extended memory into expanded memory. ILIM386.COM Displays the status of all memory in the computer. ISPEEDPC.COM Changes computer speed from the DOS prompt or a batch file. INBRDPC.SYS PARAMETERS Add the following command to the CONFIG.SYS file: DEVICE = INBRDPC.SYS [SPEED=n] [EGACACHE] [NOCACHE][NODIAGS] [NOPAUSE] [NOSCRUB] [SYSWAIT=n] [FDWAIT=n] [HDWAIT=n] The parameters in brackets are optional. Don't type the brackets. The following table describes these parameters. Optional INBRDPC.SYS Parameters 敖陳陳陳陳陳賃陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳朕 � Parameter � Meaning � 突様様様様様謡様様様様様様様様様様様様様様様様様様様様様様様様裕 � � � � SPEED=n � Set Inboard 386/PC initial operating speed to n.� � � Valid settings are 1, 2, 3, and 4. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � EGACACHE � Download EGA ROM BIOS instruction to 32-bit RAM.� 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NOCACHE � Don't download the computer's ROM BIOS � � � instructions to 32-bit RAM. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NODIAGS � Turn off memory diagnostics during power up. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NOPAUSE � Don't pause after Inboard 386/PC driver loads. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NOSCRUB � Don't initialize conventional memory during � � � power up. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � SYSWAIT=n � Set system wait states to n (don't use with � � � SPEED=n). Valid settings are 0 to 30. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � FDWAIT=n � Set floppy disk access wait states to n. � � � Valid settings are 0 to 30 (default is 16). � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � HDWAIT=n � Set hard disk access wait states to n. Valid � � � settings are 0 to 30 (default is 0). � 青陳陳陳陳陳珍陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 ILIM386.SYS PARAMETERS If you want to convert extended memory into expanded memory, add the following command to the CONFIG.SYS file: DEVICE = ILIM386.SYS [EMS=n or EXT=n] [FRAME=n] The parameters in brackets are optional. Don't type the brackets. The following table describes these parameters. Optional ILIM386.SYS Parameters 敖陳陳陳陳陳賃陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳朕 � Parameter � Meaning � 突様様様様様謡様様様様様様様様様様様様様様様様様様様様様様様様裕 � � � � EMS=n � Set amount of expanded memory to n. All � � � remaining Inboard 386/PC memory remains as � � � extended. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � EXT=n � Set the amount of extended memory to n. All � � � remaining Inboard 386/PC memory is converted to � � � expanded. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � FRAME=n � Set EMS page frame starting address to n. � � � Valid values for n are E000, DC00, D800, D400, � � � D000, CC00, C800, C400, C000 � 青陳陳陳陳陳珍陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 ICACHE.COM PARAMETERS Use the ICACHE program to create a disk cache that speeds up your hard drive. ICACHE will use all available extended memory up to 1024K bytes unless you set a size using the optional parameters. Add the following command to the AUTOEXEC.BAT file: ICACHE [/S:n] [/B-] [/T-] [/-x] The parameters in brackets are optional. Don't type the brackets. The following table describes these parameters. Optional ICACHE.COM Parameters 敖陳陳陳陳陳賃陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳朕 � Parameter � Meaning � 突様様様様様謡様様様様様様様様様様様様様様様様様様様様様様様様裕 � /S:n � Set size of cache in K-bytes to n. Valid � � � values for n are 48 to 1024. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � /B- � Disable batch copy of sectors to and from the � � � cache. Use only if experiencing high-speed data � � � communications problems. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � /T- � Disable whole-track reads. ICACHE will read � � � only requested sectors, not the entire track. � 団陳陳陳陳陳津陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � /-x � Disable caching on drive x. If drive x is a � � � partition, no partition of that drive will be � � � cached. � 青陳陳陳陳陳珍陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 ISPEEDPC.COM PARAMETERS Use the following command to change the Inboard 386 operating speed: ISPEEDPC n (valid values for n are 1, 2, 3, and 4. Speed 1 is very slow, and Speed 4 is very fast). NOTE: You can also change between speeds 1 and 4 by simultaneously pressing the Ctrl key, Alt key, left-shift key, and 1 or 4 key. The computer will beep to indicate the selected speed is active (1 beep = speed 1, 4 beeps = speed 4). ISTATPC.EXE DESCRIPTION Type ISTATPC at the DOS prompt and press Enter to view the current operating status information for your Inboard 386/PC. ILIM386.COM DESCRIPTION Type ILIM386 at the DOS prompt and press Enter to view the status of all the memory in the computer, including memory on Inboard 386/PC. ILIM386.SYS must already be loaded in the CONFIG.SYS file. 様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様 End of file Intel FaxBack # 2610 November 9,1992