ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Above Board PS/PC Technical Installation Instructions º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ABOVE BOARD PS/PC INSTALLATION INTRODUCTION ÄÄÄÄÄÄÄÄÄÄÄÄ This document contains all the information an experienced user needs to install an Above Board and its software. If you're not an experienced user, you should use the Above Board manual for installation instructions or have your dealer install the Above Board. ADDING MEMORY ÄÄÄÄÄÄÄÄÄÄÄÄÄ You can use either 64K-bit chips or 256K-bit chips on the Above Board PS/PC, but you can't use both types at the same time. For a list of chips that Intel has verified, refer to the Above Board manual or to FaxBack Document #1014, "Classic Above Board Memory Chip Compatibility." You need to use 200-nanosecond chips or faster. You must fill each column (using nine chips) to which you add chips. Leave no partially filled columns. Fill the columns in the order shown in the following diagram: For 64K-bit or 256K-bit chips ÚÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÀÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄÄÄÄÄÄÄ¿ ÚÙ 6 5 4 3 2 1 ÀÄÄÄÄÄÄÄÙ SETTING SWITCHES ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ABOVE BOARD SWITCH BLOCK ÉÍÍÍÍÍÍÍÍÍ» ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Û Û Û Û º º Û Û Û Û Û Û Û Û º º 1 2 3 4 º º 1 2 3 4 5 6 7 8 º ÈÍÑÍÑÍÑÍÑͼ ÈÍÑÍÑÍÑÍÑÍÍÍÑÍÑÍÑͼ Parallel ÀÂÙ ÀÂÙ Clock ³ ÀÂÙ ÀÄÂÄÙ ³ ÀÄÄÄÝAlways Off Port ÚÄÄÄÙ ³ ÚÄÂÄÄÄÄÄÄÄÄÁ¿ ³ ³ ³ ÚÄÂÄÂÄÄÁÄÄÄ¿ ³ ³ß³ CLK ON ³ ³ ³ ³ Chip Type ³Ü³Ü³ NONE ³ ³ ÃÄÅÄÄÄÄÄÄÄÄÄ´ ³ ³ ÀÄÂÄÂÄÄÄÄÄÄ¿ ÃÄÅÄÅÄÄÄÄÄÄ´ ³ ³Ü³ CLK OFF ³ ³ ³ ³Ü³ 64K ³ ³Ü³ß³ LPT1 ³ ³ ÀÄÁÄÄÄÄÄÄÄÄÄÙ ³ ³ ÃÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÄÄÄÄÄ´ ³ ³ ³ ³ß³ 256K ³ ³ß³Ü³ LPT2 ³ ³ ³ ³ ÀÄÁÄÄÄÄÄÄÙ ÀÄÁÄÁÄÄÄÄÄÄÙ ³ Conventional³ ³ ³ Memory Start³ ³ I/O Port for ³ Address ³ ³ Expanded Memory Serial ³ ÚÄÂÄÂÄÄÄÄÄÁ¿ ÀÂÄÂÄÂÄÂÄÄÄÄÄÄÄÄÄÄ¿ Port ³ ³Ü³ß³ 256K ³ ³Ü³Ü³Ü³NO EXP MEM³ ÚÄÂÄÂÄÄÄÁÄÄ¿ ÃÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ ³Ü³Ü³ NONE ³ ³ß³Ü³ 512K ³ ³Ü³Ü³ß³ 208-20F ³ ÃÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ ³Ü³ß³ COM1 ³ ³ß³ß³ NONE ÃÄ¿ ³Ü³ß³Ü³ 218-21F ³ ÃÄÅÄÅÄÄÄÄÄÄ´ ÀÄÁÄÁÄÄÄÄÄÄÙ ³ ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ ³ß³Ü³ COM2 ³ No ÞÄÙ ³Ü³ß³ß³ 258-25F ³ ÀÄÁÄÁÄÄÄÄÄÄÙ ConventionalÞ ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ Memory addedÞ ³ß³Ü³Ü³ 268-26F ³ ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ Note: If you have a Parallel Port on ³ß³Ü³ß³ 2A8-2AF ³ your video board, it's usually addressed ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ as LPT1. In this case, the Above Board ³ß³ß³Ü³ 2B8-2BF ³ Parallel Port is referred to as LPT2 ÃÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄÄ´ or LPT3 even though the switches are ³ß³ß³ß³ 2E8-2EF ³ set for LTP1 or LPT2. ÀÄÁÄÁÄÁÄÄÄÄÄÄÄÄÄÄÙ SYSTEM BOARD SWITCH SETTINGS FOR IBM PC If you have an IBM PC and use the Above Board PC to provide conventional memory, you need to set switches on the computer's system board. If you don't add conventional memory with the Above Board, you don't have to change the computer's switches. The following figures show the settings for IBM PC-1s and PC-2s if the Above Board provides conventional memory up to 640K bytes: ÚÄÂÄÂÄÂÄÂÄÂÄÂÄÂÄ¿ PC-1 (640K) ³Ü³Ü³Ü³Ü³ ³ ³ ³ ³ Note: The PC-1 ROM BIOS allows ÀÄÁÄÁÄÁÄÁÄÁÄÁÄÁÄÙ 544K bytes maximum. 1 2 3 4 5 6 7 8 ÚÄÂÄÂÄÂÄÂÄÂÄÂÄÂÄ¿ PC-2 (640K) ³ß³Ü³ß³ß³Ü³ ³ ³ ³ or PC-1 with ÀÄÁÄÁÄÁÄÁÄÁÄÁÄÁÄÙ upgraded BIOS 1 2 3 4 5 6 7 8 NOTE: PC-2s have a "B" stamped on their back panel, PC-1s don't. INSTALLING SOFTWARE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Installing the Above Board software involves these steps: þ Copying files þ Setting up expanded memory þ Setting up RAM disks þ Setting up a print buffer COPYING FILES Copy the files you need from the Intel diskette to your hard disk's root directory or to your system diskette. SETTING UP EXPANDED MEMORY To use expanded memory, add this line to your CONFIG.SYS file: DEVICE = EMM.SYS c m i [EXP=x] [ND] [NP] [H=x] Where the parameters without brackets ([]) are required, and those with brackets are optional. Required parameters ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ c ³ Specifies the type of computer you're using. ³ ³ ³ Valid values: ³ ³ ³ pc (Use for 8-bit systems) ³ ³ ³ mod30 (Use for IBM PS/2 Model 30) ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ m ³ Specifies the 64K-byte block of memory to which ³ ³ ³ expanded memory is mapped. Valid values: ³ ³ ³ ³ ³ ³ C400 D400 ³ ³ ³ C800 D800 ³ ³ ³ CC00 DC00 ³ ³ ³ D000 E000 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ i ³ Specifies the I/O address the Above Board uses ³ ³ ³ to access expanded memory. Valid values: ³ ³ ³ ³ ³ ³ 208 258 2A8 2E8 ³ ³ ³ 218 268 2B8 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Optional parameters ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ EXP=x ³ Lets you verify the amount of expanded memory in ³ ³ ³ the computer. "x" specifies the total expanded ³ ³ ³ memory amount. EMM generates an error message ³ ³ ³ if it finds an amount different from what you ³ ³ ³ specified. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ND ³ Instructs EMM to run abbreviated memory tests ³ ³ ³ after warm boot. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ NP ³ Instructs EMM not to pause after EMM errors or ³ ³ ³ messages. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ H=x ³ Sets EMM Handle count to "x" ("x" must be less ³ ³ ³ than 256). ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ SETTING UP RAM DISKS To use a RAM disk, add this line to your CONFIG.SYS file: DEVICE = QUIKMEM2.SYS x Where "x" specifies the size of the RAM disk in K bytes. The value for "x" must be at least 16 and can't exceed the total amount of expanded memory in the computer. Values that aren't multiples of 16 are treated as the next higher multiple of 16. You don't need to type a "K" after the number. SETTING UP A PRINT BUFFER To use a print buffer, add this line to your AUTOEXEC.BAT file: QUIKBUF2 c x d t ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ c ³ Specifies the type of computer you're using. ³ ³ ³ Valid values: ³ ³ ³ ³ ³ ³ pc (Use for 8-bit systems) ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ x ³ Specifies the size of the buffer in K bytes and ³ ³ ³ must be 32 or greater. Any value that isn't a ³ ³ ³ multiple of 16 is treated as the next-higher ³ ³ ³ multiple of 16. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ d ³ Specifies the display adapter your computer ³ ³ ³ uses. Valid values: ³ ³ ³ ³ ³ ³ M IBM Monochrome E IBM EGA ³ ³ ³ H Hercules Monochrome V IBM VGA ³ ³ ³ G IBM CGA O Other ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ t ³ Specifies the type of port to be buffered. ³ ³ ³ Valid values: ³ ³ ³ ³ ³ ³ P Parallel ³ ³ ³ S1 COM1 ³ ³ ³ S2 COM2 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ IF YOU HAVE PROBLEMS ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you receive error messages during installation that say, "One or more of the parameters are missing or invalid...", you probably have an early version of the Above Board software. You can get the latest software by contacting Intel's Customer Support or by using your modem to download the software from the Intel BBS. ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ End of file Intel FaxBack # 1212 November 9,1992