ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Above Board AT Technical Installation Instructions º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ABOVE BOARD AT INSTALLATION INTRODUCTION ÄÄÄÄÄÄÄÄÄÄÄÄ This document contains all the information an experienced user needs to install an Above Board and its software. If you're not an experienced user, you should use the Above Board manual for installation instructions or have your dealer install the Above Board. ADDING MEMORY ÄÄÄÄÄÄÄÄÄÄÄÄÄ For a list of chips that Intel has verified, refer to the Above Board manual or to FaxBack Document #1014, "Classic Above Board Memory Chip Compatibility." You can use all 256K-bit chips, or you can use 64K-bit chips for columns 1 and 2 and use 256K-bit chips for the remaining columns. (Columns 3 through 8 must contain 256K-bit chips.) You must fill two columns at a time (eighteen chips). Leave no partially filled columns. Fill the columns in the order shown in the following diagram: For 64K-bit or 256K-bit chips ÚÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÀÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄÄÁÄ¿ Ú¿ ÚÙ 8 7 6 5 4 3 2 1 ÀÄÄÄÄÙÀÄÄÄÄÄÄÄÄÙ SETTING SWITCHES ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ- ABOVE BOARD SWITCH BLOCK ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Û Û Û Û Û Û Û Û º º Û Û Û Û Û Û Û Û º º 1 2 3 4 5 6 7 8 º º 1 2 3 4 5 6 7 8 º ÈÍÑÍÍÍÍÍÑÍÑÍÍÍÍÍÑͼ ÈÍÑÍÑÍÑÍÑÍÑÍÍÍÍÍÑͼ ÀÄÄÂÄÄÙ ÀÄÄÂÄÄÙ ³ þ ÀÂÙ ÀÂÄÄÄÄÙ ³ ÀÄÄÄÄÄÄÄ¿ Memory³Must³ ³ ³ ³ Chip ³Stay³ ³I/O Ports for Extended ³ Extended ³ Type ³ Off³ ³Expanded Memory Memory ³ Memory ³ ÚÄÂÄÄÄÁÄÄ¿ ³ ÀÄÄÄÄ¿ Ending ³ Starting ³ ³Ü³ 64K ³ ³ÚÄÂÄÂÄÂÄÅÄÄÄÄÄÄÄÄÄ¿ Address ³ Address ³ ÃÄÅÄÄÄÄÄÄ´ ³³ß³Ü³ß³Ü³ 258-25Fh³ ÚÄÂÄÂÄÂÄÂÄÄÄÁÄÄ¿ ÚÄÂÄÂÄÂÄÂÄÄÁÄÄÄ¿³ß³ 256K ³ ³ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³Ü³Ü³Ü³Ü³ NONE ³ ³Ü³Ü³Ü³Ü³ NONE ³ÃÄÅÄÄÄÄÄÄ´ ³³ß³Ü³Ü³ß³ 268-26Fh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´³ß³ BOTH ³ ³ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³ß³ß³Ü³Ü³ 1.5M ³ ³ß³ß³Ü³ß³ 1.0M ³ÀÄÁÄÄÄÄÄÄÙ ³³ß³ß³ß³ß³ 208-20Fh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³ß³Ü³ß³ß³ 2.0M ³ ³ß³ß³Ü³Ü³ 1.5M ³ ³³ß³ß³ß³Ü³ 218-21Fh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³ß³Ü³ß³Ü³ 2.5M ³ ³ß³Ü³ß³ß³ 2.0M ³ ³³Ü³ß³Ü³ß³ 2A8-2AFh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÚÄÙÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³ß³Ü³Ü³ß³ 3.0M ³ ³ß³Ü³ß³Ü³ 2.5M ³ÚÄÂÄÂÄÄÄÄÁÄ¿³Ü³ß³Ü³Ü³ 2B8-2BFh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´³Ü³Ü³ NONE ³ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄÄÄÄ´ ³ß³Ü³Ü³Ü³ 3.5M ³ ³ß³Ü³Ü³ß³ 3.0M ³ÃÄÅÄÅÄÄÄÄÄÄ´³Ü³Ü³Ü³ß³ 2E8-2EFh³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´³ß³ß³ 512K ³ÀÄÁÄÁÄÁÄÁÄÄÄÄÄÄÄÄÄÙ ³Ü³ß³ß³ß³ 4.0M ³ ³ß³Ü³Ü³Ü³ 3.5M ³ÀÄÁÄÁÄÄÄÄÄÄÙ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ Conventional ³Ü³ß³ß³Ü³ 4.5M ³ ³Ü³ß³ß³ß³ 4.0M ³ Memory Starting ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ Address ³Ü³ß³Ü³ß³ 5.0M ³ ³Ü³ß³ß³Ü³ 4.5M ³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³Ü³ß³Ü³Ü³ 5.5M ³ ³Ü³ß³Ü³ß³ 5.0M ³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³Ü³Ü³ß³ß³ 6.0M ³ ³Ü³ß³Ü³Ü³ 5.5M ³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³Ü³Ü³ß³Ü³ 6.5M ³ ³Ü³Ü³ß³ß³ 6.0M ³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³Ü³Ü³Ü³ß³ 7.0M ³ ³Ü³Ü³ß³Ü³ 6.5M ³ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ÃÄÅÄÅÄÅÄÅÄÄÄÄÄÄ´ ³Ü³Ü³Ü³Ü³ 7.5M ³ ³Ü³Ü³Ü³ß³ 7.0M ³ ÀÄÁÄÁÄÁÄÁÄÄÄÄÄÄÙ ÀÄÁÄÁÄÁÄÁÄÄÄÄÄÄÙ INSTALLING SOFTWARE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Installing the Above Board software involves these steps: þ Copying files þ Setting up expanded memory þ Setting up RAM disks þ Setting up a print buffer COPYING FILES Copy the files you need from the Intel diskette to your hard disk's root directory or to your system diskette. SETTING UP EXPANDED MEMORY To use expanded memory, add this line to your CONFIG.SYS file: DEVICE = EMM.SYS c m i [EXP=x] [ND] [NP] [H=x] Where the parameters without brackets ([]) are required, and those with brackets are optional. Required parameters ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ³ÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ c ³ Specifies the type of computer you're using. ³ ³ ³ Valid value: ³ ³ ³ at (Use for 16-bit systems) ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ m ³ Specifies the 64K-byte block of memory to which ³ ³ ³ expanded memory is mapped. Valid values: ³ ³ ³ ³ ³ ³ C000 D000 ³ ³ ³ C400 ³ ³ ³ C800 ³ ³ ³ CC00 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ i ³ Specifies the I/O address the Above Board uses ³ ³ ³ to access expanded memory. Valid values: ³ ³ ³ ³ ³ ³ 208 258 2A8 2E8 ³ ³ ³ 218 268 2B8 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Optional parameters ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ- ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ EXP=x ³ Lets you verify the amount of expanded memory in ³ ³ ³ the computer. "x" specifies the total expanded ³ ³ ³ memory amount. EMM generates an error message ³ ³ ³ if it finds an amount different from what you ³ ³ ³ specified. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ND ³ Instructs EMM to run abbreviated memory tests ³ ³ ³ after warm boot. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ NP ³ Instructs EMM not to pause after EMM errors or ³ ³ ³ messages. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ H=x ³ Sets EMM Handle count to "x" ("x" must be less ³ ³ ³ than 256). ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ SETTING UP RAM DISKS To use a RAM disk, add this line to your CONFIG.SYS file: DEVICE = QUIKMEM2.SYS x Where "x" specifies the size of the RAM disk in K bytes. The value for "x" must be at least 16 and can't exceed the total amount of expanded memory in the computer. Values that aren't multiples of 16 are treated as the next higher multiple of 16. You don't need to type a "K" after the number. SETTING UP A PRINT BUFFER To use a print buffer, add this line to your AUTOEXEC.BAT file: QUIKBUF2 c x d t ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Parameter ³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ c ³ Specifies the type of computer you're using. ³ ³ ³ Valid values: ³ ³ ³ ³ ³ ³ at (Use for 16-bit systems) ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ x ³ Specifies the size of the buffer in K bytes and ³ ³ ³ must be 32 or greater. Any value that isn't a ³ ³ ³ multiple of 16 is treated as the next-higher ³ ³ ³ multiple of 16. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ d ³ Specifies the display adapter your computer ³ ³ ³ uses. Valid values: ³ ³ ³ ³ ³ ³ M IBM Monochrome E IBM EGA ³ ³ ³ H Hercules Monochrome V IBM VGA ³ ³ ³ G IBM CGA O Other ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ t ³ Specifies the type of port to be buffered. ³ ³ ³ Valid values: ³ ³ ³ ³ ³ ³ P Parallel ³ ³ ³ S1 COM1 ³ ³ ³ S2 COM2 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ IF YOU HAVE PROBLEMS ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you receive error messages during installation that say, "One or more of the parameters are missing or invalid...", you probably have an early version of the Above Board software. You can get the latest software by contacting Intel's Customer Support or by using your modem to download the software from the Intel BBS. ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ End of file Intel FaxBack # 1214 November 9,1992