浜様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様� � � � Above Board 2 Plus Technical Installation Instructions � � � 藩様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様� INTRODUCTION This document contains all the information an experienced user needs to install an Above Board 2 Plus and its software. If you're not an experienced user, you should use the Above Board manual for installation instructions or have your dealer install the Above Board. ADDING MEMORY TO THE ABOVE BOARD 2 PLUS The Above Board 2 Plus uses Single Inline Memory Modules (SIMMs). These are small circuit boards generally containing nine memory chips each. The Above Board 2 Plus uses 256K- or 1M-byte SIMMs. For a list of SIMMs that Intel has verified, refer to the Above Board manual or to FaxBack Document #1510, "Micro Channel Above Board Memory Chip Compatibility." You must install 2 SIMMs at a time, filling sockets 1 and 2 first, then 3 and 4, etc. You can use either 256K- or 1M-byte SIMMs, but not both. The following figure shows where the sockets are on the Above Board. 敖� 敖陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 � �3嬪様様様様様邑 1嬪様様様様様邑 � �4塒様様様様様余 2塒様様様様様余 � �5嬪様様様様様邑 � �6塒様様様様様余 � �7嬪様様様様様邑 � �8塒様様様様様余 � 青陳陳陳陳陳陳陳陳陳朕 攷 敖陳� � 青陳拈陳陳陳陳陳� 青陳� COPYING AN OPTION DISKETTE Start your computer from the Reference Diskette and press Enter to continue. Highlight "Copy an Option Diskette" and press Enter. Follow the instructions on the screen. CONFIGURING THE SYSTEM You MUST configure your PS/2 computer with the backup copy of the Reference Disk after installing an Above Board. Insert the Above Board and then follow these instructions. Turn on your computer and put the Reference Disk in drive A. Answer Y when asked "Automatically Configure System?". Remove the Reference diskette from drive A and reboot the computer. SOFTSET You must run the SOFTSET program to fully install the Above Board 2 Plus. SOFTSET will either create an initialization file on your computer's hard disk (if your operating system is OS/2), or it will put a device driver to initialize the Above Board 2 Plus in your CONFIG.SYS file (if your operating system is DOS). Put the Intel diskette in drive A and type A:SOFTSET. Then press Enter and follow the prompts for your specific configuration. INSTALLING THE SOFTWARE Installing the Above Board software involves running the SOFTSET program which, depending on your selections will: � Copy necessary files onto your boot disk or diskette to initialize the Above Board 2 Plus � Set up an expanded memory driver in your config.sys file � Set up RAM disk(s) driver in your config.sys file � Set up a print buffer driver in your autoexec.bat file SETTING UP EXPANDED MEMORY To use the EMM 4.0 Rev D expanded memory manager, either run the SOFTSET program or add this line to your CONFIG.SYS file: DEVICE = EMM.SYS c o [EXTF=x] [EXP=x] [ND] [NP] [NE] [H=x] [FR] [MC] [RD] [MCF=x] [MCL=x] [EXPF=x] [EXPL=x] Where the parameters without brackets ([]) are required, and those with brackets are optional. REQUIRED PARAMETERS 敖陳陳陳陳陳堕陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳朕 � Parameter � Description � 突様様様様様慷様様様様様様様様様様様様様様様様様様様様様様様様裕 � c � Specifies the type of computer you're using. � � � Valid values for EMM 4.0 Rev D Are: � � � � � � MOD50 IBM PS/2 Model 50 � � � MOD55 IBM PS/2 Model 55SX � � � MOD60 IBM PS/2 Model 60 � � � MOD65 IBM PS/2 Model 65 � � � MOD70 IBM PS/2 Model 70 & P70 � � � MOD80 IBM PS/2 Model 80 � � � � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � o � specifies the operating system you use. Valid � � � values: � � � � � � DOS DOS Operating System � � � OS2 OS/2 Operating System � 青陳陳陳陳陳祖陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 OPTIONAL PARAMETERS 敖陳陳陳陳陳堕陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳朕 � Parameter � Description � 突様様様様様慷様様様様様様様様様様様様様様様様様様様様様様様様裕 � EXTF=x � Sets the extended memory starting address for � � � Above Board to "x". SOFTSET automatically � � � calculates "x", but you can calculate "x" using � � � this formula: � � � Total extended memory - Above Board memory + 1024� � � = x. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � EXP=x � Sets amount of expanded memory to "x" K bytes. � � � Valid values are from 16 to 32768. Non-multiples� � � of 16 are rounded up to the next multiple of 16. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � ND � Instructs EMM to run abbreviated memory tests � � � after warm boot. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NP � Instructs EMM not to pause after EMM errors or � � � messages. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � NE � Instructs EMM not to run extended memory tests. � � � Don't use this parameter if the Above Board � � � supplies extended memory. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � FR � Instructs EMM to take advantage of 100-nanosecond� � � SIMMs on the Above Board, enabling 0 wait state � � � operation. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � MC � Enables mappable conventional memory. Disables � � � all memory on the computer's system board and � � � uses 640K bytes of Above Board memory as � � � conventional memory. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � RD � Relocates expanded memory driver into expanded � � � memory. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � H=x � Sets EMM Handle count to "x" ("x" must be less � � � than 256). � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � MCF=x � Sets mappable conventional memory starting � � � address to "x". Valid addresses include 4000 � � � and 8000 (4000=256K, 8000=512K) � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � MCL=x � Sets mappable conventional memory ending � � � address to "x". Valid addresses include 9800 � � � and 9C00 (9800=608K, 9C00=624K) � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � EXPF=x � Sets first 16K-byte page of the expanded memory � � � page frame to "x". (see previous section for � � � valid addresses. � 団陳陳陳陳陳田陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳調 � EXPL=x � Sets last 16K-byte page of the expanded memory � � � page frame to "x". Valid addresses are CC00, � � � D000, D400, D800, and DC00) � 青陳陳陳陳陳祖陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳陳潰 SETTING UP A RAM DISK To use a RAM disk, add this line to your CONFIG.SYS file: DEVICE = QUIKMEM2.SYS x Where "x" specifies the size of the RAM disk in K bytes. The value for "x" must be at least 16 and can't exceed the total amount of expanded memory in the computer. Values that aren't multiples of 16 are treated as the next higher multiple of 16. You don't need to type a "K" after the number. IF YOU HAVE PROBLEMS If you receive error messages during installation that say, "One or more of the parameters are missing or invalid...", you probably have an early version of the Above Board software. You can get the latest software by contacting Intel's Customer Support or by using your modem to download the software from the Intel BBS. Intel Customer Support 様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様様 End of file Intel FaxBack # 1612 August 27,1992