PRINT SELECTION FOR APAR - II06174 92/07/14                                     
APAR= II06174  SER=                            DD DOC                           
USING ATI GRAPHICS VANTAGE VIDEO CARD W/ MOUSE PORT                             
OS2INFOAPAR R200 OS2 OS/2 MICE INFOAPAR                                         
STAT= INTRAN       FESN5NFO000-000  CTID= II0000 ISEV= 4                        
SB92/07/09  RC          CL          PD           SEV= 4                         
                       PE=                       TYPE= I                        
RCOMP= INFOPCLIB    PC LIB INFO ITE RREL= R001                                  
FCOMP=                              PFREL= F     TREL= T                        
ACTION=             SEC/INT=                     DUP/                           
USPTF=              PDPTF=                       DUPS 0                         
DW92/07/09  RT          SC          FT                                          
RE          PT          UP          LP                                          
PV          AP          EN          FL                                          
LC92/07/09  RU92/07/09       MCEASPSA                                           
                             CUST INST LVL/SU=                                  
FAILING MODULE=              FAILING LVL/SU=                                    
SYSROUTE OF:          RET APAR=             PS=                                 
COMP OPER ENV=                                                                  
                                                                                
                                                                                
SYSRES=      SYSIN=      SYSOUT=      CPU=             RE-IPL=                  
OPTYPE=                 SPECIAL ACTIVITY=          REGRESSION=                  
PRE-SCREEN NO.=          RSCP= RS000                                            
ERROR DESCRIPTION:                                                              
The ATI graphics vantage video card comes with a mouse port                     
and an ATImouse.  The mouse port will accept other mice as                      
well. There tend to be problems using a mouse through this                      
port due to interupt conflicts.  But this can be resolved                       
by setting the interupts for the mouse on the video                             
board.  Follow the steps below to do this...                                    
..                                                                              
...                                                                             
1)  On disk 1 of the utilities disks which come with the                        
    board there is a program called INSTALL ( on some it                        
    is VINSTALL ).  This must be run from DOS                                   
    ( booted DOS not a vdm dos session in OS/2 ).                               
...                                                                             
2)  Select "Set Power Up Configuration".  This will list                        
    current selections for the board.                                           
...                                                                             
3)  First thing to check is the Mouse Enable/Disable                            
    selection.  Of course this must be set to enable.                           
    If it is not, then enable it.  This may be your                             
    only problem.                                                               
...                                                                             
4)  Check port addresses.  Primary should be:23C to 23F                         
                           Secondary should be  238 to 23B                      
    you should not need to mess with these.                                     
...                                                                             
5)  Set the interupt level.  The available levels are 2-5,                      
    but 2-4 are already used by the system.  5 is a good                        
    choice as long as they are only using one printer.                          
    The interupt for lpt2 is 5 but as long as the only                          
    have one printer this will be no problem.                                   
    If they want to use 2 printers, then advice them                            
    to get a converter to use the mouse in a serial port.                       
...                                                                             
...                                                                             
NOTE:  if during install they use another mouse beside                          
       the ATI, it may not work.  advise them to use                            
       the ATI mouse during the install, and then switch                        
       back if they want to use the other.                                      
...                                                                             
...                                                                             
Any other questions call ATI customer service:416-756-0711.                     
LOCAL FIX: