HP ScanJet scanners and Microsoft ® Windows 95 drivers - how to install The following instructions are for pre-installed, non-Windows 95 scanning software, HP DeskScan II, version 2.2. HP C2502 CARD (ISA WITHOUT SWITCHES) 1. Copy HPSJCLAS.DLL to the Win 95 System directory and SCANJET.INF to the Win 95 INF directory. a. Open MS-DOS prompt by clicking on Start menu - Programs and selecting MS-DOS Prompt. b. Insert the driver diskette in the floppy drive. c. At the MS-DOS prompt copy HPSJCLAS.DLL file from the diskette to the Win95 system directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\hpsjclas.dll c:\windows\system d. At the MS-DOS prompt copy SCANJET.INF file from the diskette to the Win95 INF directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\scanjet.inf c:\windows\inf e. At the MS-DOS prompt type exit to return to windows. 2. Use "Add New Hardware" in the Control Panel to add a SCSI controller. a. Select "No" when Windows 95 asks if you want it to search for new hardware. b. Select "SCSI controllers" as the hardware type. Push "Next". c. Push the "Have Disk..." button when asked to identify the manufacturer and model for your new hardware. Click "OK" to copy manufacturer files from a:\. d. Select "Symbios Logic 53C400A (HP Version) SCSI Adapter" as the model for your new hardware. Click "Next". e. Windows 95 will display which resources it plans to use for your new hardware. Click "Next" then "Finish". 3. Turn off the computer. If the card is not already physically in the computer, insert it now. Connect the scanner to the card's connector. Make sure the scanner is terminated. Make sure the scanner is turned ON prior to step 4. 4. Turn on the computer. You will be asked for the disk with the drivers on it. Specify the diskette drive location (usually a:\) . NOTE: If you are not asked for the scanner drivers at bootup (after you log in), and your scanner was turned on before and during boot, go to the System control panel (Press Start, Settings, Control Panel, then double click on System. Click on the device manager tab.). If there is a yellow exclamation mark next to the "Symbios Logic 53C400A (HP Version) SCSI Adapter" you need to adjust the resources for your card (See Windows 95 documentation for more information). Click on "Symbios Logic 53C400A (HP Version) SCSI Adapter", and the Properties button, select the "Resources" tab to examine possible device conflicts. If the "conflict device list" area shows "No conflicts" try checking the "Use automatic settings" checkbox. If there is a conflict, adjust the resources (See Windows 95 documentation). When you are done press "OK". If values selected are correct, your scanner should be detected and you will be prompted for the driver diskette. 5. Your system will reboot automatically. 6. Your drivers are now installed. Use "Scanner Test" to test the installation. NOTE: SCSI address test is not supported with Windows 95. THIRD-PARTY SCSI CARD 1. Copy HPSJCLAS.DLL to the Win 95 System directory and SCANJET.INF to the Win 95 INF directory a. Open MS-DOS prompt by clicking on Start menu - Programs and selecting MS-DOS Prompt. b. Insert the driver diskette in the floppy drive. c. At the MS-DOS prompt copy HPSJCLAS.DLL file from the diskette to the Win95 system directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\hpsjclas.dll c:\windows\system d. At the MS-DOS prompt copy SCANJET.INF file from the diskette to the Win95 INF directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\scanjet.inf c:\windows\inf 2. Use the "Device Manager" tab in "System" in the Control Panel to verify that a SCSI controller has already been installed. If not use "Add New Hardware" in the Control Panel to add the SCSI controller you own. If the SCSI controller you own is not listed as a choice in "Add New Hardware," you must contact the SCSI controllers manufacturer to obtain a Windows 95 driver. 3. Turn off the computer. If the card is not already physically in the computer, insert it now. Connect the scanner to the card's connector. Make sure that if the scanner is the last device on the SCSI chain and that it is terminated. Make sure the scanner is turned ON before step 4. 4. Turn on the computer. You will be asked for the disk with the drivers on it. NOTE: If you are not asked for the scanner drivers at bootup (after you log in), and your scanner was turned on before and during boot, go to the System control panel. (Press Start, Settings, Control Panel, then double click on System. Click on the device manager tab.) Examine your Device configuration, if there is a yellow exclamation mark next to your SCSI card you might have to adjust your card resources. Please consult Windows 95 documentation, your SCSI card documentation or your SCSI card manufacturer. 5. Your system will reboot automatically 6. Your drivers are now installed. Use "Scanner Test" to test the installation. NOTE: SCSI address test is not supported with Windows 95. HP C2503 CARD (MICROCHANNEL WITHOUT SWITCHES) 1. Identify what Input/Output (I/O) region your interface card is using. Consult the documentation that came with your computer to find out how to do this. 2. Copy HPSJCLAS.DLL to the Win 95 System directory and SCANJET.INF to the Win 95 INF directory. a. Open MS-DOS prompt by clicking on Start menu - Programs and selecting MS-DOS Prompt. b. Insert the driver diskette in the floppy drive. c. At the MS-DOS prompt copy HPSJCLAS.DLL file from the diskette to the Win95 system directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\hpsjclas.dll c:\windows\system d. At the MS-DOS prompt copy SCANJET.INF file from the diskette to the Win95 INF directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\scanjet.inf c:\windows\inf 3. Use "Add New Hardware" in the Control Panel to add your scanner and interface card. a. Select "No" when Windows 95 asks if you want it to search for new hardware. b. Select "Other devices" as the hardware type. Push "Next". c. Push the "Have Disk..." button when asked to identify the manufacturer and model for your new hardware. Click "OK" to copy manufacturer files from a:\. d. Select "HP ScanJet on C2503" as the model for your new hardware. Push "Next". e. Windows 95 will display which resources it plans to use for your new hardware. If those do not match the resources your card is set to, do not allow your computer to be shut down. Instead, go to the "Device Manager" tab in "System" in the control panel and modify the resources allocated for the "HP ScanJet on C2503" to match the card's settings. 4. Turn off the computer. If the card is not already physically in the computer, insert it now. Connect the scanner to the card's connector. Turn on the computer. 5. Your drivers are now installed. Use "Scanner Test" to test the installation. NOTE: The SCSI address test is not supported with Windows 95. HP C1752/C1753 INTERFACE CARD (ISA OR MICROCHANNEL WITH SWITCHES) 1. Identify what memory region the switches on your interface card are set to. Consult the documentation that came with your scanner to find out how to do this. 2. Copy HPSJCLAS.DLL to the Win 95 System directory and SCANJET.INF to the Win 95 INF directory. a. Open MS-DOS prompt by clicking on Start menu - Programs and selecting MS-DOS Prompt. b. Insert the driver diskette in to the floppy drive. c. At the MS-DOS prompt copy HPSJCLAS.DLL file from the diskette to the Win95 system directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\hpsjclas.dll c:\windows\system d. At the MS-DOS prompt copy SCANJET.INF file from the diskette to the Win95 INF directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\scanjet.inf c:\windows\inf 3. Use "Add New Hardware" in the Control Panel to add your scanner and interface card. a. Select "No" when Windows 95 asks if you want it to search for new hardware. b. Select "Other devices" as the hardware type. Push "Next". c. Push the "Have Disk..." button when asked to identify the manufacturer and model for your new hardware. Click "OK" to copy manufacturer files from a:\. d. Select "HP ScanJet IIc/IIp on C1752/C1753" as the model for your new hardware. Push "Next". e. Windows 95 will display which resources it plans to use for your new hardware. If those do not match the resources your card is set to, do not allow your computer to be shut down. Instead, go to the "Device Manager" tab in "System" in the control panel and modify the resources allocated for the "HP ScanJet IIc/IIp on C1752/CI753" to match the card's settings. 4. Turn off the computer. If the card is not already physically in the computer, insert it now. Connect the scanner to the card's connector. Turn on the computer. 5. Your drivers are now installed. Use "Scanner Test" to test the installation. NOTE: The SCSI address test is not supported with Windows 95. HP SCANJET PLUS SCANNER AND INTERFACE CARD 1. Identify what memory region and interrupt the switches and jumpers on your interface card are set to. Consult the documentation that came with your scanner to find out how to do this. 2. Copy HPSJCLAS.DLL to the Win 95 System directory and SCANJET.INF to the Win 95 INF directory. a. Open MS-DOS prompt by clicking on Start menu - Programs and selecting MS-DOS Prompt. b. Insert the driver diskette in to the floppy drive. c. At the MS-DOS prompt copy HPSJCLAS.DLL file from the diskette to the Win95 system directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\hpsjclas.dll c:\windows\system d. At the MS-DOS prompt copy SCANJET.INF file from the diskette to the Win95 INF directory. The following assumes that your diskette drive is a: and Win 95 was installed on C:\Windows: copy a:\scanjet.inf c:\windows\inf 3. Use "Add New Hardware" in the Control Panel to add your scanner and interface card. a. Select "No" when Windows 95 asks if you want it to search for new hardware. b. Select "Other devices" as the hardware type. Push "Next". c. Push the "Have Disk...." button when asked to identify the manufacturer and model for your new hardware. Click "OK" to copy manufacturer files from a:\. d. Select "HP ScanJet-Plus" as the model for your new hardware. Push "Next". e. Windows 95 will display which resources it plans to use for your new hardware. If those do not match the resources your card is set to, do not allow your computer to be shut down. Instead, go to the "Device Manager" tab in "System" in the control panel and modify the resources allocated for the "HP ScanJet Plus" to match the card's settings. 4. Turn off the computer. If the card is not already physically in the computer, insert it now. Connect the scanner to the card's connector. Turn on the computer. 5. Your drivers are now installed. Use "Scanner Test" to test the installation. NOTE: The SCSI address test is not supported with Windows 95. Windows is a U.S. trademark of Microsoft Corporation. Microsoft ® is a U.S. registered trademark of Microsoft Corporation. Copyright Hewlett-Packard Co. 1995 This information is subject to change without notice and is provided "as is" with no warranty. Hewlett-Packard shall not be liable for any direct, indirect, special, incidental or consequential damages in connection with the use of this material.