From: NEIL MCLAUGHLIN (8/28/95) To: Bob Mortensen Mail*Link¨ Remote Mech Warrior & Avenger Installing Avenger Support To establish Avenger support, simple run the batch file AVMECH2.BAT ex: A:> AVMECH2 This will perform two actions: 1. COPY AVENGER.DLL \MECH2\GIDDI 2. COPY AVENGER.CPC \MECH2\GIDDI You must hit ESC once inside Mech2 and select the Cockit Controls menu item. Then select Spaceball Avenger from the menu. If you wish, you can also select the Mouse, it will work concurrently with the Avenger. Please disable FlightStick if it is highlighted in red by clicking on it with the mouse. It may produce undesirable results by conflicting with the Avenger. Installing for a Custom Path If you did not select the default path setting when installing MechWarrior, you must provide the path you chose when running the batch file. ex: A:> AVMECH2 /GAMES/3D/MECH2 This will install Avenger support in that directory Controlling the MechWarrior The following paragraph will assume you are familiar with the device, and namely, the six individual axes. TX Turn legs left, right (pull left, push right) TY Jump (pull up - if jump jets available) TZ Throttle up, down (C button must be held) RX If D Button not pressed - torso pitch (look up, down) If D Button pressed - pilot pitch RY If D Button not pressed - torso turn (look left,right) If D Button pressed - pilot turn RZ NOT USED BUTTON A Weapon Cycle BUTTON B Weapon Fire BUTTON C Enable Throttle control (used with TZ) BUTTON D Enable Pilot control (turn pilots head) BUTTON E Toggles Through Targets BUTTON F Nearest Enemy Remapping the Avenger Controls Unlike most games supported by the Avenger, there is no configuration file to allow the user to remap buttons and change the feel of the game. However, you can edit the controls. Please refer to the Mech II instructions for remapping input device (Cockpit Controls - Install Guide page 19). By default, the Mech unit will recenter itself if no pressure is applied to the Avenger. You can change this to allow it to maintain its' orientation by changing Pitch and Yaw to Turn Left/Turn Right and Look Up/Look Down. These items are listed under the Buttons menu, since they are digital as opposed to analog. The AVENGER.DLL will set these accordingly to motion, and they will generate the same effect as a keystroke. You may find the response is a bit slower, and you may need to use one of the Buttons for recentering so you don't lose your orientation between the legs and torso turning. If you have any comments or suggestions, send email to jeffp@spacetec.com or neilm@spacetec.com. We welcome your ideas and will respond quickly. ------------------ RFC822 Header Follows ------------------ From NEILM@spacetec1.spacetec.com Thu Aug 17 06:20:14 1995 Received: from druidia.spacetec.com by netcomsv.netcom.com with ESMTP (8.6.12/SMI-4.1) id GAA21622; Thu, 17 Aug 1995 06:20:14 -0700 Received: from spacetec1.spacetec.com (spacetec1 [198.112.220.28]) by druidia.spacetec.com (8.6.9/8.6.9) with ESMTP id JAA20309 for ; Thu, 17 Aug 1995 09:22:20 -0400 Received: from SPACETEC1/SMTP by spacetec1.spacetec.com (Mercury 1.21); 17 Aug 95 09:25:51 EST Received: from SMTP by SPACETEC1 (Mercury 1.21); 17 Aug 95 09:25:43 EST From: "NEIL MCLAUGHLIN" Organization: Spacetec IMC Corporation To: "Bob Mortensen" Date: Thu, 17 Aug 1995 09:25:42 EST Subject: Mech Warrior & Avenger X-Confirm-Reading-To: "NEIL MCLAUGHLIN" X-pmrqc: 1 Priority: normal X-mailer: Pegasus Mail v3.22 Message-ID: <19308AE3138@spacetec1.spacetec.com> ======================================================================