About Corner

Corner is a Win95 program for calculating many apects of a corner made from sheetmaterial, e.g. steel or aluminiumfacades. You only input four - typically known - measures of the corner: the corners logical angle in degrees, the height of the cornercover (the “sill”) and the depths of the two legs of the corner. And out you get all measures necessary for cutting the sheets and perhaps assembling them at home in the workshop.

Besides the Corner.exe-file the Corner-map contains Corner.hlp, a Readme.txt and a File_id.diz.

A little about the developer

Rights and registration

Disclaimer

A little about the developer

Corner is developed as a DOS-program some 10 years ago and now converted to Borland Delphi by Henning Schulz, who has been developing specialized software in the fields of order-, stock- and productionmanaging for PCs (and before the PC for other microcomputers) for some 20 years. Distribution is through Micro-Sys ApS, owned by Henning Schulz. So contact to both Henning Schulz and Micro-Sys ApS is easiest achieved by emailing schulz@micro-sys.dk.

Back

Rights and registration

Corner is published as shareware. All rights for Corner belongs to Henning Schulz and any kind of use, copying and distribution in any form is an infringement of these rights with the specific exceptions mentioned below.

You are very welcome and in fact invited to distribute the unreregistrered sharewareversion in the complete and unchanged Corner-package - even on medias as CD-ROM publishings, BBS’es and download-sites on the Internet. Publication according to this does not give the enduser any further rights than mentioned in this chapter.

Try Corner out for 30 days before registration. Registration fee is the equivalent of 120 Dkr (at time of writing around 12 UK£, 33 DM, 19 US$, 2320 ¥).

You pay by bank- or girotransfer (from your own giro-account, in your bank or at the postoffice).

Transfer to:

Bikuben GiroBank A/S

Girostroeget 1

DK-0800 Hoeje Taastrup

Denmark

Accont: 633-9972

SWIFT: GICODKKK

At the same time you must

either on my homepage http://www.micro-sys.dk

or in an email to schulz@micro-sys.dk

or in a letter to

Micro-Sys ApS

Boegeskov Hoevej 7 C

DK-8260 Viby J

Denmark

or in the remitterspecification

inform me about

Your name.

The address you want the registrationcode forwarded to (email or snailmail).

The PRIMARY CODE written in the About-box in Corner.

When your payment is received, you get a registrationcode to enter into the Reg.code-field in the About-box. This gives you the right to use Corner without further nuisance. It is strictly forbidden to distribute the registered version in any way including - but not limited to - sale, gift, lending, renting, leasing or servicebureau-operations.

Back

Disclaimer

Corner is published “as is”. It is thoroughly tested under Windows 95 but nevertheless, any use of Corner is at your own risk. Micro-Sys ApS, the publisher, or Henning Schulz, the developer, shall not be liable for any damage whatsoever, direct or derived, in connection with using Corner, even if it turns out to be caused by Corner.

Back


Enter the horisontal angle of the corner as it appears in the final construction. The angle must be entered in degrees between 1 and 179 degrees.


Enter the horisontal depth of leg one as it appears in the final construction. The depth can be entered in any unit desired such as millimeters or inches, but the same unit must be used for both depths and the height.


Enter the horisontal depth of leg two as it appears in the final construction. The depth can be entered in any unit desired such as millimeters or inches, but the same unit must be used for both depths and the height.


Enter the vertical height of the corner as it appears in the final construction. The height can be entered in any unit desired such as millimeters or inches, but the same unit must be used for both depths and the height.