Installation Instructions for a NetWare 3.X server.

(These instructions assume that you have already installed NetWare
Connect.)  

1. Exit the NWC console if it is running.

2. Do NWCSTOP from the server console.

3. Down the server.

4. EXIT to DOS.

5. Make a directory on the server's hard drive called PATCH.

6. Make a subdirectory under PATCH called DISK1.

7. Put NWC001.EXE into the DISK1 subdirectory and unzip it:
     NWC001   <enter>

8. Make a subdirectory to PATCH called DISK2.

9. Put NWC002.EXE into the DISK2 subdirectory and unzip it:
     NWC002      <enter>   

10. RUN SERVER.EXE

11. LOAD INSTALL

12. Choose "Product Options"

13. Press INSERT

14. Enter the path to the DISK1 directory.

15. Follow the instructions  

16. Restart Netware Connect with NWCSTART.

17. Reload your AIO driver(s).

18. Copy the following new files to the remote PCs (and any
workstations on your LAN which will functioning as remotes).     
     NRN.COM*
     DIALCON.EXE*
     NETWARN.COM*

19. Copy NASI.EXE* to any workstations on your LAN which will be
functioning as remotes.

*NOTE: It is extremely important that the old versions of all 4 of
these files be replaced on ALL workstations.  

20.  Install the current SPX fix for your server: 
  A. On a NetWare 3.11 server
     - SPXFIX2.NLM     8/20/93
     - SPXDDFIX.NLM    9/20/93
     - SPXFSFIX.NLM    8/20/93
     - SPXLISFX.NLM    8/20/93
     - XMDFIX.NLM      9/15/92
     - PATCHMAN.NLM    2/4/93
     - IPXS.NLM        8/10/93
     - STREAMS.NLM     7/20/93
     - SPXS.NLM        9/14/93
     - TLI.NLM         9/14/93
  These 10 files are in STRTL2.EXE which can be found in Library 4 of
  NOVLIB.

  B. On a NetWare 3.12 server
     - SPXDDFIX.NLM    9/20/93
     - PM312.NLM       11/11/93
     - IPXS.NLM        8/10/93
     - STREAMS.NLM     7/20/93
     - SPXS.NLM        9/14/93
     - TLI.NLM         9/14/93
These 6 files are in STRTL2.EXE, which can be found in Library 4 of
NOVLIB.
 
21. See item #1 in "Solutions Specifics" of NWC001, for instructions
regarding the use of the new NetWarn utility.

NOTES
----- 
Reinstalling NetWare Connect
If you reinstall NetWare Connect, do not try to use an old
NWCSTART.NCF file.
 
Using NRN over X.25
To use NRN to connect to an X.25 network, do the following:
  - Specify the Modem type as "Manual" in DIALCON.
  - Add the /PASS option on the server, as follows, when you load
  AIOPAD:
     load aiopad x25board=boardname x25port=portnumber /pass
 
The /PASS option disables AIOPAD from performing X.3 processing in
data transfer mode.  This allows RNS to operate more efficiently.
Using the /PASS option, however, prevents the user from going into
command mode and changing the X.3 PAD parameters.