ÛßÛ ÛßßÛ ÛßßÛ ÛßßÛ Û Û ÛßßÛ Û Û ÛßßÛ Ûßßß Ûßßß ÛßÛ ÛßßÛ Û Û Û ÛßßÛ Û Û Û Û ßßßÛ ÛßßÛ Û ßÛ Ûß ÛßßÛ ßßßß ßßßß ßßßß ß ß ßß ßßßß ßßßß ß ß ßßßß ßßßß ß ß ÛßßÛ Ûßßß ßßßÛ ÛßßÛ ßÛß Ûßßß ÛßßÛ Û ÛßßÛ Û Û Û Û ßßßÛ ÜÜ Ûßßß Û Û Û ßßßÛ Ûßßß Û ÛßßÛ ßßßÛ ßßßß ßßßß ßßßß ßßßß ßßß ßßßß ß ßßßß ß ß ßßßß ÛßßÛ ÛßÛ ßÛß Û Û Ûßßß ÛßÛ Ûßßß Û Û ÛßßÛ Û Û Û Ûß ÛßßÛ ßßßÛ ßßßß ß ß ßßß ßß ßßßß ß ß ßßßß Installation of Boca Research Voyager SVCXL1-2 Video Drivers Copyright (c) 1995, Boca Research Inc. All Rights Reserved ------------------------------------------------------------ ******************************* Warning *********************************** Before installation of any SVGA display driver, the system display should be set to VGA mode. DO NOT install this driver package if the system display is set to anything other than 640x480x16 VGA mode. To restore VGA mode, use Selective Install and select VGA for Primary Display, or run the SETVGA utility. **************************************************************************** Table of Contents: 1) A note for modem users. 2) Installation. 3) Changing Resolutions AFTER installing. 4) Miscellaneous. %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ÛßÛßÛ ÛßßÛ ÛßßÛ Ûßßß ÛßÛßÛ Û Û Ûßßß Ûßßß ÛßÛ Ûßßß Û Û Û Û Û Û Û Ûß Û Û Û Û Û ßßßÛ Ûß ÛßßÛ ßßßÛ ß ß ßßßß ßßßß ßßßß ß ß ßßßß ßßßß ßßßß ß ß ßßßß If you downloaded the drivers from a B.B.S.; CompuServe; Genie; America OnLine, or any other on-line service you must label the floppy disk you create as: DISP 1 After you download the file, follow these steps: 1. Insert a blank, formatted floppy diskette in your 'A' drive. 2. In a DOS box, type in PKUNZIP A:, where is the path and name of the file you downloaded. 3. Type in the following command: LABEL A:DISP 1 4. Continue with the instructions below. %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ============================================================================ INSTALLATION ============================================================================ Before installation of any SVGA display driver, the system display should be set to VGA mode. DO NOT install this driver package if the system display is set to anything other than 640x480x16 VGA mode. To restore VGA mode, use Selective Install and select VGA for Primary Display, or run the SETVGA utility. 1. Open an OS/2 full-screen or windowed session 2. Insert Display Diskette in Drive A: 3. At the OS/2 Command Prompt, enter the following command: A:\INST2X A: C: ;; on OS/2 2.0,2.1 systems A:\INST30 A: C: ;; on WARP OS/2 3.0 systems where A: is the source drive C: is the boot drive where OS/2 2.x is installed **NOTE** If installing this driver package on OS/2 3.0 ( WARP ) MAKE SURE you use INST30.CMD The command file will copy the following files to C: C:\OS2\SVGA.EXE -- original saved as SVGA.ESV C:\OS2\INSTALL\DSPINSTL.EXE -- original saved as DSPINSTL.211 C:\OS2\SCREEN01.SYS -- original saved as SCREEN01.SSV C:\OS2\MDOS\VSVGA.SYS C:\OS2\CHIPS.SYS C:\OS2\INSTALL\CT64300.DSC 4: When INSTALL completes, do a system SHUTDOWN and REBOOT. This is required to load SCREEN01.SYS which has been modified to correctly identify the display adapter. 5: After the system has been rebooted do the following: 5a: Start DSPINSTL -------------------------------------------------------------------- * On OS/2 2.x Systems Open an OS/2 Full Screen or Windowed session. At the OS/2 command prompt type DSPINSTL to install new device driver and configure the video system. * On OS/2 3.0 (WARP) Systems Go to the System Setup folder and run Selective Install to install new device driver and configure the video system. DO NOT use DSPINSTL on WARP systems. -------------------------------------------------------------------- 5b: Run DSPINSTL Follow the DSPINSTL or Selective Install session prompts to complete the installation. 5c: Select Primary Display 5d: From the list of Primary Display Adapter Types, Select: Boca Research Voyager SVCXL1-2 5e: Click on 'OK' from the "System Configuration" dialog box. 5f: Click on 'Install' from the "OS/2 Setup and Installation" dialog box. 5g: OS/2 then asks for the 'Source Directory'. Do not be confused. Type in either A:\ or B:\ (depending on where the SVCXL1/2 OS/2 Driver Disk is inserted) 5h: From the list of available Display Resolutions, select a display resolution ============================================================================ Changing Resolutions AFTER installing (see above) ============================================================================ ALWAYS use the INSTxx.CMD on this source disk for the FIRST install of Boca Research Voyager SVCXL1-2 To switch to a different video resolution, follow STEP 5 above. ============================================================================ Miscellaneous ============================================================================ OS/2 PM Display Drivers ----------------------- The following display resolutions are available with this release: 640x480x256 Color CRT 60Hz 800x600x256 Color CRT 60Hz 1024x768x256 Color CRT 60Hz Non-Interlaced Seamless Windows Support ------------------------ This release of the OS/2 2.1 Device Driver for Boca Research Voyager SVCXL1-2 supports Seamless Windows. WIN OS/2 Full Screen -------------------- The Windows 3.1 drivers provided with this release are enhanced mode drivers. The following display resolutions are provided: 640x480x256 Color CRT 60Hz 800x600x256 Color CRT 60Hz 1024x768x256 Color CRT 60Hz Non-Interlaced The WIN-OS/2 Full Screen session setting WIN_RUN_MODE should be set to Enhanced Capability. The default setting is Standard Mode. WIN-OS/2 should be started by selecting the WIN-OS/2 Full Screen Icon in the Command Prompts folder, or with the WIN command in a DOS Full Screen OS/2 Full Screen session. DO NOT start WIN-OS/2 in a DOS or OS/2 Window. The system does not support the enhanced video mode being used in a window, and therefore will not run. DO NOT use ALT-HOME to switch a DOS or OS/2 Full Screen session to Windowed when running WIN-OS/2. -----------*----------