IBM....................LAN Server 2.0

  IBM LAN SERVER 2.0 INSTALLATION NOTES:
  FOR THE INTEL EtherExpress(tm) 16 FAMILY OF NETWORK ADAPTERS
  ============================================================

  This document applies to the EtherExpress(tm) 16, 16TP, 16C, MCA, and
  MCA/TP.  It contains notes for installing the NDIS driver.  It does
  not explain how to configure an EtherExpress board.  For instructions
  about configuring the board, see either the Expert's Guide or the
  Complete Guide.


  INTRODUCTION:
  -------------
  Before you begin, you will need the I/O address of the EtherExpress
  adapter.  You can get this information by running SOFTSET on the
  EtherExpress 16 or the IBM SC program on the EtherExpress MCA.

  This installation does not use OS/2 Extended Services.


  OS/2 2.0 AND LAN SERVER 2.0:
  ----------------------------
  1. Follow the normal LAN Server installation procedure using the LAN
     Services Installation/Configuration.

  2. Select:
     - Advanced Installation 
     - Install and Configure this Workstation
     - Configure a component
     - LAN Adapter and Protocol Support
     - Copy additional network adapter drivers
     - Enter the path for the EtherExpress NDIS driver.

        A:\NDIS

     - Insert the EtherExpress driver diskette in drive A:

  3. After the adapter driver is copied select, "Configure
     workstation" and configure your workstation to meet your
     requirements.  Refer the IBM documentation for more help.  For
     more information about adapter configuration parameters see the
     section "Configuring the MAC Driver" in the Adapter Guide to
     Operation.


  4. The installation and configuration will:

     - Copy the files to the C:\IBMCOM\MACS directory

       EXP16.OS2     OS/2 driver
       EXP16.DOS     DOs driver
       EXP16.NIF     network interface file (used by configuration utility)
       PROTOCOL.INI  Protocol.ini stub for the the EtherExpress card

     - The complete Protocol.ini file will be created and put in the 
       C:\IBMCOM directory.

   5. Exit the Installation program, but before rebooting the computer,
      edit the Config.sys file and add the line:

       DEVICE=C:\IBMCOM\MACS\EXP16.OS2

      NOTE: Because of a bug in the IBM Installation/Configuration
            program, this device driver line will be removed everytime
            you run the Configuration program.  So, everytime you
            run the Configuration program, you must manually add
            this line.


  EXAMPLE PROTOCOL.INI FILE:
  --------------------------

   [PROT_MAN]
    DriverName = PROTMAN$

   [IBMLXCFG]
    EXP16_nif = EXP16.nif
    NETBEUI_nif = NETBEUI.nif

   ;*----------------------------------------------*
   ;*------------- PROTOCOL SECTION ---------------*
   ;*----------------------------------------------*

   [NETBEUI_nif]
    DriverName = netbeui$
    Bindings = EXP16_nif
    ETHERAND_TYPE = "I"
    USEADDRREV = "YES"
    SESSIONS = 40
    NCBS = 95
    NAMES = 21
    SELECTORS = 5
    USEMAXDATAGRAM = "NO"
    ADAPTRATE = 1000
    WINDOWERRORS = 0
    TI = 30000
    T1 = 500
    T2 = 200
    MAXIN = 1
    MAXOUT = 1
    NETBIOSTIMEOUT = 500
    NETBIOSRETRIES = 8
    NAMECACHE = 0
    PIGGYBACKACKS = 1
    DATAGRAMPACKETS = 2
    PACKETS = 350
    PIPELINE = 5
    MAXTRANSMITS = 6
    MINTRANSMITS = 2
    DLCRETRIES = 5

   ;*----------------------------------------------*
   ;*--------------- MAC SECTION ------------------*
   ;*----------------------------------------------*

   [EXP16_nif]
    DriverName = EXP16$
    IOADDRESS = 0x300