2.2 servers 

  NETWARE 2.2 SERVER INSTALLATION NOTES:
  FOR THE INTEL EtherExpress(tm) 16 FAMILY OF NETWORK ADAPTERS
  ============================================================

  This document applies to the EtherExpress(tm) 16, 16 TP, 16C, MCA,
  and MCA TP.  It contains notes for installing the NetWare 2.2 server
  driver.  It does not explain how to configure an EtherExpress board.
  For instructions about configuring the board, see either the Expert's
  Guide or the Complete Guide for your board.

  This document is also available on FaxBACK.  Document #6312.

  INTRODUCTION:
  -------------
  To setup a Novell NetWare 2.2 server, you "tell" NetWare what
  hardware you have in the server and the configuration settings of
  that hardware.  You then install User Services and make them
  available to your users.

  You can install NetWare from the network or from the NetWare
  diskettes.  This document assumes you are installing Novell NetWare
  2.2 from diskettes.

  For complete information on setting up a server, see the Novell
  NetWare documentation.

  
  PROCEDURE:
  ----------
  1. Run INSTALL from a backup copy of the Novell NetWare System-1 disk. 
     When asked which installation method you want (Basic or Advanced),
     choose ADVANCED.

     NOTE: The original Novell NetWare diskettes are write protected. 
           Follow Novell's instructions for making writeable backups 
           before you run Novell's INSTALL program.

  2. A few screens into the program you will be asked to setup your
     network adapter and your disk controller.  Highlight NETWORK BOARD A
     and press Enter.  A list of available adapters will appear.  Press
     the Insert key and you will be asked to insert a disk into a drive. 
     Insert the Intel EtherExpress diskette in a drive and press Enter.

  3. After a few seconds three versions of the EtherExpress driver will be
     added to the list of available drivers.

     Intel EtherExpress 16 Driver          ver#  date
     Intel EtherExpress 16 Driver  w/AT 1  ver#  date
     Intel EtherExpress 16 Driver  w/AT 2  ver#  date

     The first driver (no notation before the version number) is a
     standard NetWare 286 server driver, but contains no AppleTalk
     support.  The next driver (w/AT 1) includes support for AppleTalk
     phase 1, and the last driver (w/AT 2) includes support for AppleTalk
     phase 2.  

     Select the appropriate driver and press Enter.  (If you are not sure
     which version of AppleTalk you are running, see your Novell
     documentation.)

  4. You should now be at the Network Adapter and Disk Controller screen
     again.

	 Select CONFIGURATION OPTION and you will see the following list:

     option 0    IOAddress 300
     option 1    IOAddress 310
     option 2    IOAddress 320
     option 3    IOAddress 220
     option 4    Driver configurable by the Jumpers utility

     Select the I/O Address you specified and press Enter.  (The I/O
     address is setup in SOFTSET for the EtherExpress 16 and the System
     Configuration program for the EtherExpress MCA.)

     If the I/O Address you selected is not in this list, select option 4
     (Driver configurable by the Jumpers utility).  After you complete the
     INSTALL program, you will need to run the Novell Jumpers utility (on
     NET$OS.EXE) and update the I/O Address selection for the EtherExpress
     board.

  5. Now you can setup the network address and disk controller as
     specified in Novell's documentation.

  6. Next you will be asked to swap a several disks.  When asked to insert
     the LAN_DRV_453 disk, put the Intel EtherExpress disk in drive A. 
     This will copy the needed files to the correct location.

     NOTE: If you are using a backup copy of the EtherExpress disk,
           the volume label must be LAN_DRV_453.

     Continue with the installation procedure as directed in the Novell
     documentation.

  
  NETWARE 2.1X:
  -------------
  NetWare version 2.1x uses a program called NETGEN to setup and
  configure the server.  See Novell's documentation for information
  about running NETGEN.  The options for the EtherExpress board will be
  the same as in the NetWare 2.2 installation.

  MEMORY MAPPED MODE:
  -------------------
  You should only have one EtherExpress 16 in memory mapped mode in
  NetWare 2.2 server.  If you have two EtherExpress cards set to memory
  mapped mode, the second one will automatically switch to I/O mapped
  mode.

  MULTIPLE CARDS IN SERVER:
  -------------------------
  The EtherExpress NetWare 2.2 server driver supports one or two cards
  in the server.  NetWare 2.2 allows up to four network cards
  (LAN A-D) in the server.  However, there is a size limit on the
  network card's OBJ file to be able to accomplish this.  The total OBJ
  size must be less than 20-25K depending on the version.  If you
  exceed this limit, you get a linking error when the NET$OS is being
  created.  INSTALL doesn't say why the the linking error, only that
  one occurred.  To eliminate the error, you must remove a network card
  from the server and rerun INSTALL.