TBIT3000.ram contents: ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Initialize Port ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ ³ ³ ³ Modem Name : Telebit 3000 ³ ³ Port # : 1 ³ ³ Port's IRQ : 4 ³ ³ Base address : 03F8 ³ ³ Baud rate : 9600 ³ ³ Modem delay : 1500 ³ ³ Reset command: AT&F9 ³ ³ Setup # 1 : ATE0V1&C1&D3X1S59=1&W ³ ³ Setup # 2 : ATS51=7&W ³ ³ Setup # 3 : ³ ³ Write NRam : ³ ³ Dump NRam : ³ ³ Notes : Use this file to write setup to NRAM then you will ³ ³ SET WCMDM=TBIT3000 in your CAT(x).bat. If you use ³ ³ other than 57600 DTE remember to set S51 register. ³ ³ ³ ³ F2 - Save Record F3 - Load Record F10 - Open Port ³ ³ ³ ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ; TBIT3000.mdm contents: ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ MDM Record - Part 1 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ ³ ³ ³ 1. Communications port number : 1 ³ ³ 2. Communication port IRQ : 4 ³ ³ 3. Communication port base address : 03F8 ³ ³ 4. Determine ringing using : Ring detect ³ ³ 5. Determine baud rate using : Result code 1 ³ ³ 6. Initialize port at what baud rate : 57600 ³ ³ 7. Lock DTE at initialization baud rate : Y ³ ³ 8. Use CTS/RTS flow control : Y ³ ³ 9. Number of seconds to wait for carrier : 30 ³ ³ 10. Milliseconds before answering : 1000 ³ ³ 11. Milliseconds to lower DTR for hangup : 2000 ³ ³ 12. Milliseconds to delay before prelog : 1000 ³ ³ 13. Milliseconds to wait for result code : 2800 ³ ³ 14. Milliseconds between command strings : 2000 ³ ³ 15. Trigger level for FIFO : 4 ³ ³ ³ ³ ³ ³ F2 - Save Record F3 - Load Record PgDn - Part 2 ³ ³ ³ ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ; ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ MDM Record - Part 2 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ ³ ³ ³ 1. Verbal code for RING : RING ³ ³ 2. Verbal code for 300 baud : CONNECT ³ ³ 3. Verbal code for 1200 baud : 1200 ³ ³ 4. Verbal code for 2400 baud : 2400 ³ ³ 5. Verbal code for 4800 baud : 4800 ³ ³ 6. Verbal code for 9600 baud : 9600 ³ ³ 7. Verbal code for 14400 baud : 14400 ³ ³ 8. Verbal code for 19200 baud : 19200 ³ ³ 9. Verbal code for 38400 baud : 38400 ³ ³ 10. Verbal code for 57600 baud : 57600 ³ ³ 11. Modem error correction codes : LAP|REL ³ ³ 12. Modem on-hook string : ATH0 ³ ³ 13. Modem off-hook string : ATH1 ³ ³ 14. Modem reset string : ATZ0 ³ ³ 15. Modem initialization string : ATE0V1&C1&D3X1S51=7S59=1 ³ ³ 16. Modem answer string : ATA ³ ³ ³ ³ F2 - Save Record F3 - Load Record PgUp - Part 1 ³ ³ ³ ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;