Using the Compucom Speedmodem with RemoteAccess BBS Software:

This is by no means a technical document on all the different ways to
initialize your CompuCom Speedmodem for RA v.10, but a SIMPLE guide...

oo ..Be sure the Speedmodem ROM version is at least 2.51. Type ATI3...
\/ ..from any communications program in TERMINAL mode for results...
   ..EXAMPLE: (c) Copyright CompuCom 1990 V2.51

oo ..RA REQUIRES a FOSSIL. Be sure to setup your com-port correctly...
\/ ..Refer to your Remote Access documentation, X00.SYS example below.
   ..Modify CONFIG.SYS with the line, refer to DOS if needed...
   ..DEVICE=C:\X00.SYS E T=2048 R=2048 1=2F8,IRQ3 B,1,19200...(For Com2)

oo ..Run RACONFIG.EXE then choose MODEM then SETUP...
\/
               Modem      Other
          ÑÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÑÍÍÍÍ
          ³*Setup*         ³±±±±
          ³ Initialization ³±±±±
          ³ Errorlevels    ³±±±±
          ³ Restrictions   ³±±±±
          ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;±±±±

ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍSetupÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
³                                            ³
³ Comport                : 2                 ³
³ Maximum baud           : 19200             ³
³ Init response          : OK                ³
³ Busy response          : OK                ³
³ Ring string            : RING              ³
³ Error free connect     : REL               ³
³ Connect 300            : CONNECT|          ³
³ Connect 1200           : CONNECT 1200      ³
³ Connect 2400           : CONNECT 2400      ³
³ Connect 4800           : CONNECT 4800      ³
³ Connect 9600           : CONNECT 9600      ³
³ Connect 19k            : CONNECT FAST      ³
³ Connect 38k            : CONNECT FASTER    ³
³ Automatic answer       : Yes               ³
³ Modem delay            : 200               ³
³ Outbound buffer size   : 5                 ³
³ Send break to clear    : No                ³
³                                            ³
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;

oo ..Then press ESC and choose Initialization...
\/
                         Modem      Other
                    ÑÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÑÍÍÍ
                    ³ Setup          ³±±±     ....................
                    ³*Initialization*..... oo ..Actually spelled..
                    ³ Errorlevels    ³±±±  \/ ..Initiali(s)ation..
                    ³ Restrictions   ³±±±     ..in Remote Access..
                    ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;±±±     .......(smile)......
                    ±±±±±±±±±±±±±±±±±±±±±
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍInitialisationÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
³                                                                     ³
³ Initialization tries : 10                                           ³
³ Initialization string: AT&F2*H2%C0&C1&D2H0S0=0M0&W|                 ³
³ Busy string          : ATH1|                                        ³
³ Answer string        : ATA|                                         ³
³                                                                     ³
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;

oo AT&F2 +F *H2%C0 &C1&D2H0S0=0M0 &W
\/ |___| |  |____| |____________| |_____WRITE to FIRMWARE!
...|     F  |      |
...|     A  |      Recommended for RA!
...|     X  |
...|     |  Depends on error mode wanted       ..............
...|     O  *H1 or *H2    (MNP-5)              ...REFER to...
...|     F  *H1 or *H2%C0 (MNP-4) -|Recommend  ... Manual ...
...|     F  *H1 or *H2\N0 (no MNP)-|either one ..............
...|     |
...|     For COMBO only, do NOT use on CHAMP. Not Used on roms after 4/1/91
...|
...A must for Speedmodem!

oo ..*H2%C0 can be substituted with other variations...
\/ ..as recommended in the Speedmodem manual...

oo ..If using the COMBO, add +F to the Initialization string...
\/ ..turns fax off on the COMBO, returns ERROR on the CHAMP...


Dialing out:

oo ..RTS-CTS ON, ALL BAUD at 19200, AUTO BAUD DETECT OFF...
\/
  ...When using a long distance carrier with the Speedmodem...
  ...call your LD customer service and ask if a "carrier code"...
  ...is needed for proper "bandwidth" on "asynchronous" connections...

oo ..An example where this code is needed is the US Sprint...
\/ ..FIBER OPTIC NETWORK, to access a ""full-bandwidth" line...
  ...the code 10333 is needed, that is dial 10333-1-800-000-0000...
  ...this ensures that the FULL bandwidth is available to you...
  ...otherwise, a sudden "No carrier" can result...

Well, this by no means covers all the ways to use RA-BBS with a Compucom
Speedmodem.  But it should help you initially (pun?).  If all else fails,
don't forget to read the doc's!

    <End of File>