Using the Compucom Speedmodem with SPITFIRE 3.0 BBS Software: This is by no means a technical document on all the different ways to initialize your CompuCom Speedmodem for SPITFIRE, but a SIMPLE guide. oo ..Be sure the Speedmodem ROM version is at least 2.51. Type ATI3... \/ ..from any communications program in TERMINAL mode for results... ..EXAMPLE: (c) Copyright CompuCom 1990 V2.51 oo ..Refer to the init string below... \/ SPITFIRE /I19200 /C2 /M AT&F2 +F *H2%C0 S0=0S2=1&C1&D2V1Q0M0H0X1&W | | | |___| | |____| |________________________| | | | | F | | | | | | A | Recommended for Spitfire! | | | | X | | | | | | Depends on error mode wanted | | | | O *H1 or *H2 (MNP-5) | | | | F *H1 or *H2%C0 (MNP-4) -|Recommend | | | | F *H1 or *H2\N0 (no MNP)-|either one | | | | | | | | | For COMBO only, do NOT use on CHAMP. | | | | NOT USED FOR Roms after 4/1/91 | | | A must for Speedmodem! | | | | | OVERRIDES Spitfire init string... | | | Selects com port... | Locks the port... oo ..Place it in the file SF.BAT that starts Spitfire... \/ ..(I.E.) :LOOP C:\ CD\SF SPITFIRE /I19200 /C2 /M AT&F2+F*H2%C0S0=0S2=1&C1&D2V1Q0M0H0X1&W ^^Not for roms after 4/1/91 oo ..It is a good idea to change the actual string within Spitfire... \/ ÕÍ[ SPITFIRE NODE 1 MODEM CONFIGURATION ]ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ ³ ³ ³ Serial Port No................. : 2 ³ ³ System Baud Rate............... : 19200 ³ ³ Initialization String.......... : ³ ³ AT&F2*H2%C0S0=0S2=1&C1&D2V1Q0M0X1H0&W ³ ³ Modem - Error Correction Type.. : Yes ³ ³ Error Correction Message....... : REL ³ ³ Hardware Data Flow Control..... : Yes ³ ³ Answer On What Ring............ : 1 ³ ³ Display Result Messages........ : On ³ ³ Disconnect Delay............... : 3 ³ ³ Use High Speed Async Routines.. : Yes/No oo ..Either way works..³ ³ Baud Rate Requirement.......... : 0 \/ ³ ³ ³ ³ Enter Command or uit - ³ ³ ³ ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ; oo ..*H2%C0 can be substituted with other variations... \/ ..as recommended in the Speedmodem manual... oo ..If using the COMBO, add +F to the Initialization string... \/ ..turns fax off on the COMBO, returns ERROR on the CHAMP... NOTE: +F NOT USED for roms after 4/1/91 Dialing out: oo ..RTS-CTS ON, ALL BAUD at 19200, AUTO BAUD DETECT OFF... \/ ..When using a long distance carrier with the Speedmodem... ..call your LD customer service and ask if a "carrier code"... ..is needed for proper "bandwidth" on "asynchronous" connections... oo ..An example where this code is needed is the US Sprint... \/ ..FIBER OPTIC NETWORK, to access a ""full-bandwidth" line... ..the code 10333 is needed, that is dial 10333-1-800-000-0000... ..this ensures that the FULL bandwidth is available to you... ..otherwise, a sudden "No carrier" can result... This by no means covers all the ways to use SPITFIRE with a Compucom Speedmodem. But it should help you initially (pun?). If all else fails, don't forget to read the doc's!