ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Configuring Communications Software: Qmodem 5.x º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ QMODEM SatisFAXtion/100: Intel's lab tested this software (versions 3.1 & 5.x) with the SatisFAXtion/100 board, and it is compatible. SatisFAXtion/400: Intel's lab tested this software (versions 4.2 & 5.x) with the SatisFAXtion/400 board, and it is compatible. Intel Modems: This program is compatible with Intel modems. Configuring the Program: The first time you run Qmodem it automatically takes you to the "Setup Menu". After the first time, use to call up the "Setup Menu". o Press M to select the Modem menu o Press Q to select "Quick Modem Config" - Highlight the Intel modem selection that best describes your modem then press Intel 9600EX V32 with V.42bis For: 9600EX, 14.4EX, SatisFAXtion 400 & 400E Intel 2400EX MNP For: 2400 baud Intel modems o A configuration screen will now ask: - "Send these commands to the modem [Y/N]?" - Select Y for yes o Press C to select "Communications Parameters" - Press A to select "Default baud rate" - Highlight the baud rate for your modem then press -------------------------------------------------------- Intel SatisFAXtion 400/400E : 57600 Intel High Speed V.42bis modems : 38400 (or higher) Intel 2400 V.42bis modems : 9600 Intel 2400B MNP modems : 4800 Intel non MNP modems : 2400 - Press J to select "Serial Port" - Type the number of the COM port of your modem and press - Press o Press M to select "Modem Commands" - Press I to select "Initialization Command" - Type ATZ^M then press . - Press NOTE: QMODEM Comes with COM1 and COM2 defined, but COM3 and COM4 are undefined. If you installed your modem on COM3 or COM4, use the following commands to define the address and IRQ for COM3 or COM4. If you installed your modem on COM1 or COM2, skip over this section to the next. o If you installed your modem on COM3 or COM4, press P to select "Port Addresses" then follow these instructions: - Highlight the "Base" address of your modem's COM port then - Type 0, your modem's 3 digit address (3E8 for COM3 or 2E8 for COM4), then press - Highlight the "IRQ" of your modem's COM port then - Type your modem's IRQ number then - Press twice o Press H to select "Host" options menu. - Press I to select "Init Command". - Type ATZS0=1^M (delete any extra characters) then . NOTE: For Intel faxmodems, the number following "S0=" should match the number of rings you specified in the SatisFAXtion SETUP program. - Press A to select "Answer Command" then delete ATA^M and leave the field blank. - Press o Press M to select "Modems" - Press T to select "Toggles" - Set the following option for your modem: non-MNP MNP V.42bis ------- ----- ------- [XON/XOFF] Flow ctrl. ON OFF OFF CTS/RTS signal OFF ON ON RTS When writing OFF OFF OFF Fifo during shell Lock DTE baud rate ON ON ON High speed Xmit ON ON ON 16550 UART enable [ ON if you have one ] INIT ignores CD ON ON ON - twice o Press E to select "Exit" - Press S to select "Save changes" o Now configure your modem. - In terminal mode, enter the correct command for your modem: Intel V.42bis modems (1,2): AT&F&W Intel 2400B MNP modems (3): AT&F\N3\Q3\J0&W Intel non-MNP modems (4) : AT&F&C1&D2&W That's all there is to it! ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ End of file Intel FaxBack # 4341 April 22,1993