Document Number 1101
Mouse Parameters for version 6.2x:
12/30/92


Basic parameters for all mice:

  *Ballistic Effect*
	
BHIGH   - Sets the ballistic effect to high.
BLOW    - Sets the ballistic effect to low.
BON     - Turns the ballistic effect on.
BOFF    - Turns the ballistic effect off.

  *Sensitivity*

S00-S10 - Set the degree of sensitivity for the mouse.
	  (example MOUSE S06 or MOUSE S09)

  *Button Swap*

SWAP    - Toggles the left and right mouse button functionality.
MSWAP   - Toggles the middle and right mouse button functionality.
	  NOTE: For TrackMan Portable users, left button corresponds
		to top button and right button corresponds to the
		bottom button.

  *Parameters*

/?      - Lists some of the mouse parameters and their description

  *Status*

?       - The status parameter displays the current mouse driver
	  settings.

  *Number of Buttons*

2K      - Sets the middle mouse button to act like a Left-Right button 
3K      - Sets the middle mouse button to act as a separate button.

  *Cursor Enhancement*

Cenhance- Loads cursor enhancements with default settings.

	  NOTE: This parameter will only work when first loading the
		mouse driver.
CSLOW   - Sets text mouse cursor to blink slow.
CFAST   - Sets text mouse cursor to blink fast.
COFF    - Sets text mouse cursor not to blink.
LCURSOR - Displays hardware text cursor with a rectangular block, and 
	  displays the graphics with a reverse video block.
DCURSOR - Disables lcursor.
TON     - Displayed hardware and software text cursor with a tail.
TOFF    - Disables the tail.

  *Drag-Lock*
 
DLEFT   - Sets the left or top button for drag-lock.
DRIGHT  - Sets the right or bottom button for drag-lock.
DNONE   - Disables drag-lock.

  *Remove from Memory*

OUT     - Removes the mouse driver from memory.

	  NOTE: If you use the OUT parameter, you must remove MOUSE,
		LOGIMENU, and CLICK in the reverse order that you
		load them.

 *Type*

	Note: These parameters will work only when first loading
	      the mouse driver in memory.
			  
BUS     - Forces the driver to look at the bus port.
PS2     - Forces the driver to look at the PS/2 port.
SER     - Forces the driver to look at the serial port.
1       - Configures the mouse for COM port 1.
2       - Configures the mouse for COM port 2.
     

 Mouse Driver Parameters for SERIAL MICE:

	NOTE: Parameters with a "C" in parenthesis will work with the
	      Series 7 and 9 type mouse. Parameters with an "M" in
	      parenthesis will work with Series M mice. Type MOUSE ?
	      to find out which type of mouse is being used.

 *Report Rate*

10 (C)  - Sets the report rate (signal per second from the mouse to the
	  computer) to 10.
50 (C)  - Sets the report rate to 50.
150 (C) - Sets the report rate to 150.

 *Baud Rate*

1200 (C)- Sets the report rate (information exchange rate between the mouse
	  and the computer) to 1200.
2400 (C)- Sets the baud rate to 2400.
4800 (C)- Sets the baud rate to 4800.
9600 (C)- Sets the baud rate to 9600.

 *Protocol*

MM (C)  - Sets the protocol (data tranmission regulator) for MM Series mouse.
5b (C)  - Sets the protocol for 5-byte packed binary.
RE (C)  - Sets the protocol for relative bit pad one.
MI (M)  - Sets the protocol to two-button Microsoft compatible three-byte
	  format.
MP (M)  - Sets the protocol to three-button Microsoft compatible four-byte
	  format.

 *Inital Settings*

INIT    - Resets the mouse driver

  (M) Cordless  - Report 100, Baud 9600, Protocol MP.
  (M)           - Report 100, Baud 1200, Protocol MP.
  (C)           - Report 150, Baud 2400, Protocol MM.