Setup for Zoom 28.8 VFX Modem
                       with Front Door Mailer, BGFAX 
                       and Spitfire BBS.
                      ================================
 
                                                      May 29,1994
                                              Revised September 9,1994
 
 This setup seems to work with the Zoom 28. ZFX and ZFP modems
 and the problem I was having with it not hanging up after
 connecting with certain modems. I have been tinkering with
 this for a while and so far this is the string that seems to
 work best.
 
 Run your terminal program and type: AT&F 
 This restores factory defaults.
 
 Then type:
 ATM0&C1&D3&S1&T5S11=50S7=70&W0
 
 
 Init-1 ATZ|
 Init-2 AT%C2%E3\L1+FCR=1;FDCC=1,5,0,2,0,0,0,0|
 Init-3 ATM0S7=200S95=127+FLID="203 732-5746"|
                                ^^^^^^^^^^^^^
                                This is my fax # (put yours here)
 
 
 Front Door modem Commands:
 
 Return Online ~AT0|
 Offhook       ~~ATM0H1|
 Onhook        ATH0|
 Down          ~~ATM0H1|
 
 Front Door answer control setup:
 Force Answer AT+FAA=1;A|
 
 
 The Down commands will take the modem offhook and stay offhook
 whenever Front Door exits. (Version FD 2.12sw)
  
  What these commands mean:
  
  M0  - Turns modem speaker off.
        (Almost off. I can still faintly hear it)
  
  &C1 - RLSD (DCD) Follows remote carrier.
  
  &D3 - DTR drop causes modem to do soft reset &Y setting
        determines which NVRAM profile is loaded.
  
  &T5 - Ignores remote modem request for digital loopback.
        This definitely helped the no hangup problem.
  
  S95=127 - Give extended connect message responses. 
            Data compression, error correction and protocol.
            I'll take as much info as possible.
  
  S7=70  - Remote carrier wait time in seconds.
           (I had to kick it up to 200 for BGFAXin the init string)
  
  %C2    - Enables V.42bis compression.
           Without it I got better transfer speeds, but the
           screen refreshes were too jerky so I think you
           are better off using it.
  
  %E3    - Enables monitoring, retraining and fast hangup.
           I tried %E2 but this worked best.

  /L1    - Uses interactive block mode for MNP connection
           Increased transfer speed.
  
  &W0    - Writes the initialization to NVRAM. 
   
   If you have any questions feel free to contact me at 
   FidoNet 1:141/1295 or SFNET A0203000.
                       
                                        Bob Dunn
                                        Glass Onion
                                        Ansonia, CT USA
                                        (203) 732-5746
ACTIVE PROFILE:
B1 E1 L1 M0 N1 Q0 T V1 W0 X4 Y0 &C1 &D3 &G0 &J0 &K3 &Q5 &R1 &S1 &T5 &X0 
&Y0
S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:070 S08:002 
S09:006 S10:014 S11:050 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000 
S38:020 S44:020 S46:138 S48:007 S95:127 

STORED PROFILE 0:
B1 E1 L1 M0 N1 Q0 T V1 W0 X4 Y0 &C1 &D3 &G0 &J0 &K3 &Q5 &R1 &S1 &T5 &X0 
S00:000 S02:043 S06:002 S07:070 S08:002 S09:006 S10:014 S11:050 S12:050 
S18:000 S36:007 S37:000 S40:105 S41:194 S46:138 S95:127 

STORED PROFILE 1:
B1 E0 L1 M0 N1 Q0 T V1 W1 X4 Y0 &C1 &D3 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0 
S00:000 S02:043 S06:002 S07:060 S08:002 S09:006 S10:014 S11:095 S12:050 
S18:000 S36:007 S37:000 S40:105 S41:135 S46:138 S95:255 

TELEPHONE NUMBERS:
0=                                     1=
2=                                     3=

OK