Due to the number of requests from sysop's on "how" to set up
THD ProScan to work with their BBS programs, I am including this explanation 
for setup in Telegard 2.7 and for T.A.G. 2.6c.
     Although it works equally well with other BBS programs, These are the 
only two programs which I feel qualified to advise on proper installation.
     But first a multi-purpose batch file for those wishing to test numerous 
files in a single directory.

                           GENERAL PURPOSE BATCH FILE
                           --------------------------
DIRTEST.BAT
-----------
@ECHO OFF
CTTY CON
FOR %%F IN (%1\*.*) DO C:\THDPRO\THDPRO.EXE %%F


This will cause all files in the supplied directory to be tested. However, 
be warned that only the errorlevel from the last file tested will be 
returned to the calling program.
Syntax for this batch file would be C:\THDPRO\DIRTEST.BAT C:\TEST
where DIRTEST.BAT is located in "C:\THDPRO" and "C:\TEST" is the directory 
containing the files to be tested.

                                  TELEGARD 2.7
                                  ------------
     Lets start from scratch..
make a dir called C:\THDPRO
change to that directory.
unzip THDpro-5 into that directory (or unarj, whatever).
run THDINSTL.EXE
answer all the questions and double check the settings on the final two
     screens as if your life depended on it's being correct.
change to your BBS directory.
type TELEGARD -K
press "P"
look at option "L".. make note of the path here
shell to dos.
go to the directory just seen in option "L".
copy THDPRO.EXE from C:\THDPRO\ to this directory.
return to TG (exit shell).
press "F"
press "A"
press "M"
press "1" (which I assume will correspond to the "ZIP" archive type)
check the first option to be sure it is marked "ACTIVE" (if not mark it
     active).
change line "#6" to read "THDPRO.EXE @F"
Press "Q" until you are back at the "WFC" screen and from their do a local
     logon.
Once logged on.. Go to the file section and list the files long enough to
     find the name of a single valid "zip" file.
now type at the menu prompt "//\\AT"
enter the name of the "zip" filename you just found using "list"
answer no to delete files question.. and No to search all dirs question.
watch the output on your side to see if the file is being scanned.

     The ONLY reason that this process (if followed EXACTLY) would not 
work.. is because you have no directory listed under option "L" (as above). 
IF you do not have a directory specified there, then change the "line #6" 
mentioned above to include the full path "C:\THDPRO\THDPRO.EXE @F".. DO NOT 
enter this if there is a path in option "L" or the archive tester will not 
be found.
     Also.. you might wish to test it from the command line as follows to be 
sure that it works.
type
C:\THDPRO\THDPRO.EXE C:\COMMAND.COM
     This will show you the scanner at work and if you do not see this type
of screen when run it from TG.. then you have failed in configuring TG NOT 
the fault of the scanner.
     This is FAR more detailed than I had ever hoped to have to get. Any TG 
sysop should be able to accomplish this without such detail.. BUT given that 
you may never have had to do this before.. Follow the instructions 
EXACTLY!!!!

                                  T.A.G. 2.6c
                                  --------

     T.A.G. is very simple to set up. T.A.G. simply runs a file called
"FILETEST.BAT" (found in the main BBS directory). So to set up T.A.G. you 
need only make your FILETEST.BAT read as follows...

FILETEST.BAT
------------
CTTY CON
C:\THDPRO\THDPRO.EXE %1%2.%3 {optional comport #}

This will cause all uploaded files to be tested by THDPRO.EXE in the 
directory "C:\THDPRO". The "optional comport #" is for use with systems 
running multi-nodes where the output is to be sent to a comport other than 
the one configured directly into the program. This parameter is to be ONLY a 
single digit between 0 and 8.