Easy and Step by Step Visual Guide Setup Tutorial for Interfacing Wildcat! v4.x with FidoNet. Using Wildcat! BBS v4.x, HyperMail! v1.0x and InterMail v2.29 version 1.0 InterMail v2.29 Setup Part Written by: Mufutau Towobola P.O. Box 860 Bronx, New York 10468 All Rights Reserved October 17, 1994 Fidonet address 1:278/111 Systematic BBS Node 1: (718) 716-6198 Node 2: (718) 716-6341 Modems in Operation at Systematic BBS includes the following: USRobotics Dual Standard 28.8k v.Everything Practical Peripherals FXSA 14,400 Zoom 28.8k VFC Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ º Shell to DOS º º Quit º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍͼ InterMail 2.29/demo; InterEcho 1.00; SETUP Copyright 1988-1994 Scandinavian PC Systems AB & InterZone Software, Inc. All rights reserved. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Invoke temporary DOS shell. Use Alt-Z in input fields, etc. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º NOTE: My home directory for InterMail is C:\IM (This is NOT the default º º upon installation!). You should make changes to the appropriate path º º when you are installing InterMail to be the same with this documentation.º º Look at all the required paths in the next pages on this documentation. º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ This will be your opening screen of Intermail setup, when you execute IMSETUP from inside Intermail directory: i.e. C:\IM Please adjust all your settings in Intermail to match as you see them in this documentation. Before you start the actual setup, it's better for you to already know the Network (Net) address in your area, as this will be required for this setup. Please replace any occurrence of the address here which is 1:278/9999 with your area address and your temporary Node address. Example: Zone:Area Net/9999 will translate to: 1:278/9999 for my area. Zone is: 1 ----> This is Zone for North America (includes USA & Canada) Net is: 278 ----> This is your demographical area FidoNet Net. Node is: 9999 ----> This is temporary in all Net for new Node application. Below is the most frequent asked question: Question: How do I know which FidoNet Network (Net) serves my area? Answer: There are many Fidonet Network (Net) addresses in USA and the world, so this will be based on your geographical area. The best way to found out is to call any BBS in your area that belongs to FidoNet for the Net that serves your area. Any FidoNet member BBS will be willing to give you this information. Just ask him with courtesy and tell him you also run a BBS and wants to join FidoNet. This is the opening screen of Intermail v2.29 will henceforth be referred to as IM. You get to this menu by changing to your directory called C:\IM that you have previous created and Unzip the IM files into. Moving around in IM setup comprises of using right and left arrow keys, up and down arrow keys, Enter key, and Esc to leave one menu and to save what you have entered in the options. Any screen or screens or menu omitted from this setup is then not required to complete our FidoNet setup and you should not have to worry about it. This is the beginning of the end to your FidoNet interface. For Next Menu, now highlight Global with your right arrow key. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ º Mail Server º º Address º º Filenames º º General º º Site info º º Users º ÈÍÍÍÍÍÍÍÍÍÍÍÍͼ InterMail 2.29/demo; InterEcho 1.00; SETUP Copyright 1988-1994 Scandinavian PC Systems AB & InterZone Software, Inc. All rights reserved. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Select Mail Server to configure in multi-line environments GLOBAL SETUP: ============= This is GLOBAL Menu Setup with other sub-menus that we shall complete. This is where you tell IM your Main Address and your other AKA addresses that you will use for other Networks you will be carrying using your Mailer (IM). Your directories and sub-directories will also be specified so that IM will know where your files are located. Throughout this menu setups, I have used my own Name, FidoNet address, location, modem speed, and telephone number, as an example for your setup and should be replaced with your own area temporary Fidonet address, and replaced whenever you received your own actual address from your Area Network Co-Ordinator, also known as NC. Following are the Lists of All FidoNet Zones in use: Zones Geographical Areas ===== ================== 1 North America (including USA & Canada) 2 Europe 3 Australia, Tasmania, & New Zealand 4 Latin America 5 Africa 6 Asia Note: Zones 7 and higher ==> are used for several other Private Networks FidoNet Organizations only uses Zones 1 to 6. So feel free to use any number from 7 and higher to form your own Private Network using FidoNet compatible standard and use the Node address as your AKAs. Now highlight Address and press Enter for next menu screen. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÚÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Address »ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³º Main 1:278/9999 º ³º Aka 1 º ³º Aka 2 º ³º Aka 3 º ³º Aka 4 º ³º Aka 5 º Àº Aka 6 º º Aka 7 º º Aka 8 º º Aka 19 º º Aka 20 º ÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Network address maintenance This is where you will enter your FidoNet Main Address and your other Network address called AKA, if you belong to other Network that has their own Private Nodelist. Highlight Main Address and press enter to your enter your temporary address like 1:278/9999 please replace mine above with your own area Net number. If you have AKA, highlight the AKA option and enter your other Private Network address there. Press Esc to save. Example: Let's say you are in USA and your Area Net Number is 278. Because you do not have an address yet, you will then put 1:278/9999 as your temporary address until you get your own actual address from your NC. The Node address 999 or 9999 is always reserved in each Net area for new Member applying for new Node Number like you. So you must use 999 or 9999 temporarily until your Area FidoNet NC assigns you your own Node address. After you have been assigned your own Node address, you MUST go thru this setup again to change all the occurrence of the temporary address to your actual given address. This is very important for you to remember and understand. Note: If you are not going to join FidoNet, but just needed this setup for a Local or Private Network that you want to belong thru your Mailer (IM) then you can use their address as your Main Address instead of it as an AKA. There is a lot of dis-advantage of not joining FidoNet; you will not have access to all FidoNet Message conferences, and you will not be able to communicate with other thousands of FidoNet Members and they will not be able to communicate with you either, because you will not be listed in the international Fidonet Nodelist. So you should think about obtaining your own FidoNet address for more advantages and international exposures. NOTE: If you also have any other Network address, like I personally have for my AfroNet Network (Blacks/African American Network) which is 101:13/106, I will then enter that address on the line with AKA 1, just like I have done for the FidoNet address. If you need more information on joining AfroNet, please FREQ (File REQuest) Filename: AFRONET.ZIP or MagicName: AFRONET from me at 1:278/111 Now highlight Filenames and press enter key for next sub-menu. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Mail Server ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Filenames and paths » º º º System C:\IM\SYSTEM\ º º Netmail C:\IM\NETMAIL\ º º Files C:\IM\FILES\ º º Sec Files C:\IM\FILES\ º º*Packets C:\IM\PACKETS\ º º*Log file C:\IM\IM.LOG º º Banner C:\IM\BANNER.TXT º º Nodelist C:\IM\NODELIST\ º º In-event C:\IM\EVENT.TXT º º Hudsonfmt º º Wildcat! C:\WC40\ º º Swapping C:\IM\SWAP\ º º Semaphore C:\IM\SEMA\ º º º º * = Must be unique for each Mail Server º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Where InterMail's system files are located This is the screen where you will specify where all your files are located. Please accept the file directories and filenames above as they are to make your setup easy, smooth, and straight-forward, if you change the directory structures or the filenames, you will have to remember and make changes to all the batch files enclosed and all other settings that refers to the above directories. If you have followed the instructions given at the beginning of this setup, you should have already had this directories made. Note: Make sure your Files and SecFiles directory are the same as given above. BANNER.TXT is the file that will be displayed to the caller after they press Esc twice to enter your BBS (board), sample file enclosed, please edit. EVENT.TXT is the file that will be displayed to the caller when your BBS cannot take calls like during an Events or the Zone mail Hour (ZMH), sample enclosed. All the other names are directories and sub-directories, and don't forget the ending back-slash (\) after all the directory names as seen above. Please do not put (\) back-slash after the followings: IM.LOG, BANNER.TXT, and EVENT.TXT as those are not directories but actual filenames. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ General » ³º º ³º Your country code 1 º ³º Screen flickers No º ³º Use "fastkey" Yes º ³º Screen blanking Yes º Àº ÀBlackout timer 20 º º Extended keyboard Yes º º Force 24-hour fmt No º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Copyright 1988-1994 Scandinavian PC Systems AB & InterZone Software, Inc. All rights reserved. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Your country code Self explanatory. The country telephone code should always be 1 (one) for USA, all others replace with your country telephone code. All other should be left as they are, unless you need to change them to suit your own system. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Mail Server ³ ³ Address ³ ³ Filenames ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Site Information » º º º System name Systematic BBS º º Location Bronx NY º º Country U.S.A. º º Phone 1-718-716-6198 º º Nodelist flags XX,CM,V32B,V42B,MNP º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ All rights reserved. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ The name of this system or office As you can see the above is self explanatory. Your BBS information goes here. Change the above to reflect your actual information. Do not forget to enter your phone number the way you see above, with 1 for your long distance, then your area code and followed by your local number. If this setup is used any other place other than USA please adjust as appropriate to fit your country code. Flags: Please leave the flags as I have entered above unless you are not using a high speed modem. If you are using high speed modem, the above is perfect for your setup. You MUST however have CM, XX, no-matter what!. If you are using a 2400 Modem without error correction then the Flags should only have CM,XX but if your 2400 Modem has an error correction protocol you can include it like MNP. Press Esc to save all options and highlight Users for next sub-menu. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ User maintenance » º º º Username Access º º 1 Mufutau Towobola Supervisor º º 2 º º 3 º º 4 º º 5 º º 6 º º 7 º º 8 º º 9 º º 10 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ You must specify your name here as you have specified in your BBS as Sysop. And you must also give yourself the "Supervisor" access as seen above. Please take out my name above and replace with yours. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ º Miscellaneous º º Log º º File requests º º IMServer º º External mail º º Display º º Colors º º Hidden dial info º º Function keys º º Errorlevels º º Audio control º º Swapping º º Protection º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Miscellaneous options MAILER SETUP: ============ This is one of the main important menus of your setup and proper attention should be paid to this menus and all sub-menu items below it. I have made sure the settings are right and correct for normal operation and under normal circumstances, you should not have to change anything, so leave them at default as above until you mastered the way Intermail and Mailers works. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Miscellaneous »ÍÍÍÍÍÍÍÍÍÍÍÍ º º º Mail from unlisted systems Yes º º Mail from "unprotected" systems Yes º º Mail from unlisted points Yes º º Kill empty received messages Yes º º Terminal-only (no mail) No º º Mail-only (no BBS) No º º Match remote's zone Yes º º Present all AKAs to remote system Yes º º Trigger exit upon receipt of netmail Yes º º ÀÄUpon receipt of ANY file Yes º º Print received messages No º º Busy retries 15 º º Resend retries 4 º º Retry delay 15 º º Delay before first call No º º Days to keep mail history 30 º º BBS software name Wildcat! º º Seconds before passing to BBS 15 º º Minimum undialable cost 0 º º º ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼrver: 001 ÃÄ Accept mail from systems not listed in your nodelist Please leave the above setup as they are. They are the perfect settings for your mailer operations. The above settings should work for anyone under normal circumstances. BBS Software Name: You can change or replace the Wildcat! under the option "BBS Software Name" to an abbreviation of your BBS name as to fit in the space provided, I have mine as: Systematic Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Log » ³º º ³º ! Fatal errors Yes º ³º ? Other errors Yes º ³º $ Accounting info Yes º ³º * Sent/Rcvd files Yes º ³º : Forwarding of mail Yes º ³º + Brief messages Yes º ³º - Trivial messages Yes º ³º % Transfer throughput Yes º ³º ~ Session information Yes º ³º = Modem responses Yes º ³º DEBUG: All of the above No º Àº º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ You should also leave the above settings the way they are. no adjustment needed. Note: Please DO NOT set the DEBUG to Yes, unless you want your hard drive to be filled with IM.LOG. Leave DEBUG setting at NO. Note2: You can delete your IM.LOG when it's getting too big, and Intermail will create a new one if it cannot found the old one. So it's safe to delete the log file to save on drive space. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ File requests » º º º Mode Anyone can request º º List C:\IM\MAGIC.LST º º Alias C:\IM\MAGIC.LST º º Message C:\IM\FAILED.TXT º º Max match 5 º º Max time 30 º º Max size 0 º º Min speed 2400 º º Limited Yes º º Start 07:00 º º End 04:00 º º Days -------A º º External º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Systems allowed to make file requests This is the sub-menu where you will give details info to IM of where to found the files that contains the path, directory names , filenames and MagicName so other Mailers can File REQuest (FREQ or DOWNLOAD) files from your system. The above should be correct and not need any modification. I have included sample format files for MAGIC.LST and FAILED.TXT in this archive and should already be in your C:\IM\SYSTEM directory if you have followed the instructions at the beginning of this setup process. You should take a look at this two files and edit them to suit your own system. Make sure you include the proper Magic Names and directory names for all your downloadable files as you have seen in format of MAGIC.LST included. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Display » ³º º ³º Mail waiting flashing Yes º ³º Display clock Yes º ³º Screen size 25 º ³º º ³ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Hidden dial info ³ ³ Function keys ³ ³ Errorlevels ³ ³ Audio control ³ ³ Swapping ³ ³ Protection ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ If you want the 'Mail' (waiting) notice to flash The above setup is self explanatory and should not be edited. Leave the above settings alone as they appear above. They are perfect settings for everyone. Anytime you receive a netmail from another mailer, you will see on the lower right hand corner a flashing yellow text saying "Mails" Display clock means the present time will be displayed on the "Waiting for Caller" screen, on the top right hand corner. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Log ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Function keys » º º º Shift º º F1 BBS Local Logon F1 º º F2 F2 º º F3 F3 º º F4 F4 º º F5 F5 º º F6 F6 º º F7 F7 º º F8 Dos shell / no rescan F8 º º F9 F9 º º F10 MENU F10 º º F11 F11 º º F12 F12 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Press the key you wish to change or Esc to exit This is where you will define function keys that can be used for any purpose by pressing the corresponding function key at the "Waiting for caller" screen of Intermail. I have setup the F1 key as example to give you a local login directly to your BBS. If you take a look at CAT.BAT you will see the line that says "IF ERRORLEVEL 60 goto LOCAL-BBS", use my example to define other function keys for your other purposes. I have several that does different things for me. If you cannot understand the procedure, then leave it alone until you have become an expert with IM. Note: Move on to the next screen by pressing F1 function key now, to see how this function key was created or implemented. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Log ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ F1 » º º º Title BBS Local Logon º º Action ?60 º º Pause No º º Check No º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ F6 F6 ³ ³ F7 F7 ³ ³ F8 Dos shell / no rescan F8 ³ ³ F9 F9 ³ ³ F10 MENU F10 ³ ³ F11 F11 ³ ³ F12 F12 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Title to appear in listing If you press F1 key from the previous screen you will get this sub-menu screen. Title: The is the description of what you want the F1 to do. Action: Is the errorlevel you have defined and assigned to this function in your CAT.BAT. You must also include the first question mark (?) before the errorlevel. See "If errorlevel 60 goto Local-bbs" in your CAT.BAT. Pause: Not really important. Better to be NO Check: Not really important. Could be YES or NO Now, you can later experiment by creating F2 function key for your Offline Mail Reader or something of such. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍ Errorlevels » ³º º ³º Received mail 255 º ³º Create BAT.file Yes º ³º º ³ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Colors ³ ³ Hidden dial info ³ ³ Function keys ³ ³ Errorlevels ³ ³ Audio control ³ ³ Swapping ³ ³ Protection ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Errorlevel for received conference mail and BBS batch file Received Mail: This errorlevel 255 is what we have defined in our CAT.BAT for IM to exit when another Mailer send us Netmail or files, or when you poll (call) your HUB for mails. IM will exit and execute your Mail Scanner/Tosser (Wildmail, GoMail, Interecho, Hypermail etc. ) and process the mail you just received by inserting or importing them into your BBS message conferences. Please leave this at errorlevel 255 as seen above. Create BAT. File: This option MUST be set to YES. IM will create a file called DOBBS.BAT which will inform our EXEBBS.BAT (enclosed in this archive) the modem speed, com port, minutes left before an event, or if caller is connected with Error correction modem, and all this information will be passed to the batch file that starts our BBS. Please you must leave this option set to YES. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Audio control » ³º º ³º Clock No º ³º Unpacked any mail No º ³º Unpacked high priority mail No º ³º Waiting mail No º ³º Inbound connection Yes º ³º Outbound connection Yes º ³º Completed mail transfer Yes º ³º BBS caller Yes º ³º Fatal error Yes º ³º Audio start time 06:00 º ³º Audio end time 23:00 º Àº º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ This is where you control how and when you want IM to beep (audio) when any of the above occasion occurs. I have made sure the above will be best for everyone, you may change it if the above does not suit you personally, but I think you should leave them the way they are until you know what you are doing. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Log ³ ³ File requests ³ ³ IMServer ³ ³ External mail ³ ³ Display ³ ³ Colors ³ ³ Hidden dial info ³ ³ Function keys ³ ³ Errorlevels ³ ³ÉÍÍÍÍÍÍÍÍ Swapping » ³º º ³º Swapping Yes º Àº Use LIM/EMS Yes º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Whether or not swapping should be enabled When you highlight the option "Swapping" and press enter key, you will get this sub-menu. If you have EMS/XMS, you should leave the above option the way they are, but if you do not have any EMS/XMS you should set the Swapping to NO. Having EMS/XMS will make IM perform efficiently and faster. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍ Protection » ³º º ³º Password º ³º Quit º ³º DOS shell º ³º Function keys º ³º Request files º ³º Transmit files º ³º Send mail º ³º Forced poll º ³º Nodelist º ³º Mail queue º ³º Printer º Àº º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Protect access to DOS shell, queue manager, nodelist compiler, etc. Protection options are not really needed and they should be left the way they are unless you operate your system in an environment where security is a matter of importance. But personally, I recommend you leave them alone. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ º Miscellaneous º º Keyboard macros º º Origin lines º º Colors º º Xlat.In º º Xlat.Out º º Swapping º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ EDITOR SETUP: ============= This is another important setup in IM setup. Please leave the options as they have be entered. The settings here will control how you write Netmail message thru the Intermail Netmail Message Editor. You can start the Netmail Message Editor from the IM "Waiting for Caller Screen" by pressing ALT+E. Please leave all the options under this sub-menu as they are seen in the pages to come. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍÍÍÍÍÍÍÍÍ Miscellaneous » ³º º ³º Netmail.Restricted No º ³º Netmail.Read-only No º ³º Netmail.Export OK Yes º ³º Netmail.Use tables No º ³º Netmail.Crash Yes º Àº Netmail.Direct Yes º º Netmail.Hold No º º Netmail.Private Yes º º Netmail.Kill/Sent No º º Screen size 25 º º Show hard CRs No º º Margin 75 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Restrict netmail folder This is how you want any Netmail Message written by you or any sent to your system behaves. The above settings should not be changed under normal operation. This settings should be fine for anyone. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Keyboard macros ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º º º F1 %help º º F2 º º F3 º º F4 º º F5 Mufutau| º º F6 Mufutau Towobola| º º F7 º º F8 º º F9 º º F10 %menu º º F11 º º F12 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Press the key you wish to change or Esc to exit PgDn Keyboard Macros: This are the macros that will perform a specific function when a function key is pressed for execution. The above macros should have been created for you when you initially installed Intermail. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Origin lines »ÍÍÍ º 1 Systematic BBS, Bronx, New York, USA. (718) 716-6198 º º 2 º º 3 º º 4 º º 5 º º 19 º º 20 º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Appended to messages in "Echo" folders with "Echo info" enabled This is where you will define your IM default "Origin Lines". Please change my info above and replace with your system information. Press enter key to edit. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Keyboard macros ³ ³ Origin lines ³ ³ Colors ³ ³ Xlat.In ³ ³ Xlat.Out ³ ³ÉÍÍÍÍÍÍÍÍ Swapping » Àº º º Swapping Yes º º Use LIM/EMS Yes º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Whether or not swapping should be enabled When you highlight the option "Swapping" and press enter key, you will get this sub-menu. If you have EMS/XMS, you should leave the above option the way they are, but if you do not have any EMS/XMS you should set the Swapping to NO. Having EMS/XMS will make IM perform efficiently and faster. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ º Miscellaneous º º Keyboard macros º º Xlat.In º º Xlat.Out º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Miscellaneous terminal settings TERMINAL SETUP: =============== Terminal menu setup is only needed if you will also be using IM as your communication program like QModem, Procomm Plus, Telix. etc. Because IM also has a built-in communication program which you can access by pressing ALT+J from the IM "Waiting for Caller Screen". I have enclosed a sample setup for your need here. If you will not be using IM as your communication program, then you can just leave the setup alone, as this setup has nothing to do with the operation of your Mailer or in anyway with your Fidonet setup. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Init ATM1Z| º º Download C:\IM\FILES\ º º Upload º º Editor º º Protocol Zmodem º º Emulation ANSI º º Avatar Yes º º Buffer 64 º º Connect noise Yes º º Transfer noise Yes º º Use tables No º º Auto Zmodem Yes º º Local echo No º º Wrap around Yes º º Screen size 25 º º Delay 10 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Modem initialization Please replace the Init String above with your normal init string from your communication program, or just leave the above with the default as seen. The rest of the screen options should be correct as seen above for normal operations. I have used above settings successfully. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ Miscellaneous ³ ³ Keyboard macros ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Default macro keys » º º º Shift Ctrl º º F1 Mufutau Towobola| F1 º º F2 F2 º º F3 F3 º º F11 F11 º º F12 F12 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Press the key you wish to change or Esc to exit Keyboard Macros: This are the macros that will perform a specific function when a function key is pressed for execution. The above macros should have been created for you when you initially installed Intermail. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍÍ º Modem Selection º º Limited hours º º Advanced setup º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Selection of the type of modem installed MODEM SETUP: ============ This is another MOST important part of your IM setup, because without this, you will have no mailer, and your IM will never know how to talk to your modem. This is where you will define all your modem settings and characteristics, com port, init strings, etc. Highlight the first option and press enter key to proceed to the next menu. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Modem Selection »³ º Aceex 9600 V.32 º³ º Aceex 14400 V32bis V42bis º³ º Anchor 2400i ºÙ º AT&T/Paradyne Dataport 14.4/Fax º º Best 1200 Plus º º Best 2400 Plus º º Best 2400 L º º Boca 28.8 V.FC/FAX º º Cardinal 9600V42 º º Discovery 1200H º º Discovery 2400H º º Discovery 2400C º º Galaxy Apollo º º Galaxy Apollo with MNP 5 º º Galaxy UFO º º Galaxy UFO with MNP5 º º Galaxy UFO with MNP5/V42bis º º Generic 1200 º º Generic 2400 º º Hayes 1200 º ÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼserver: 001 ÃÄ Selection of the type of modem installed Intermail comes pre-defined with some modems setup files, and when you press Modem selection you get a screen similar to the above for you to select the modem that matches your own modem, if your modem is not listed here, just select any modem closed to it. You can found extra modem files at Intermail Support BBS as listed in your Intermail archive files. If your modem is not listed here or none of the modem come close to your modem don't worry because you will have opportunity to define your own custom modem file based on the modem init strings that you have been using successfully. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍ Limited hours »³ º º³ º Limited hours No º³ º Starting time 00:00 ºÙ º Ending time 00:00 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ If enabled, InterMail will only answer the phone between the specified hours if your board is running part-time for those who are not running full-time BBS, here is where you will specify the starting time and ending time for the hour of operation, you will also need to toggle Limited hours to YES. If you are running a fulltime or 24 hours BBS or Mailer, then you should and MUST leave the above option settings the way they are. You do not need to change anything here. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ³ÉÍÍÍÍ Advanced setup » ³º Hardware º ³º Messages º Àº Command strings º º Answer control º º Connect strings º º Dial command file º º Export modem file º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Miscellaneous hardware options The options above is where you will tell IM all your Modems and hardware settings, and you should go thru settings one at a time, they are all analyzed and discussed in the next screen and most of them are self explanatory. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Hardware »ÄÄÄ¿ º º ³ º Modem port 1 º ³ º Maximum baud rate 38400 º ³ º Lock port Yes º ³ º Reset modem to connect speed No º ³ º Lower DTR when busy No º ³ º Lower DTR to terminate call Yes º ³ º Toggle DTR before dialing No ºÄÄÄÙ º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Serial port: Which com port your modem is connected, IM will not work without a modem connected to your com port, even for testing. Lock Port: If you have locked your fossil or port as explained above, please set this option to YES, if you are using 2400 baud modem and have not locked your fossil driver or port, set this option to NO. Maximum Baud Rate: The speed you have locked your com port in your port or fossil driver. If you use 2400 baud modem, you do not need to lock your com port just set this to 2400, but if you have any modem with 9600 baud and above, lock your fossil driver or com port for better result and put the speed you locked the fossil driver here. Lower DTR to terminate call: This is set YES so that IM will take the phone off-hook and keep it on busy signal when it exits to process the events or to process mails when received. If you don't want the phone off-hook, then set this to NO. But it's better when set to YES and just disable your modem speaker noise with L0 M0 command in your modem init strings. Note: You do not need to load a fossil driver for Intermail, but I have found out that loading a fossil driver does enhance Intermail performance. You should leave all the other option settings as they are seen above. Note: See Fossil Driver installation options on the other document. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Messages »ÄÄÄÄ¿ º º ³ º Error ERROR º ³ º Busy BUSY º ³ º No Carrier NO CARRIER º ³ º Ok OK º ³ º Ring RING| º ³ º No Dialtone NO DIAL TONE º ³ º No Answer NO ANSWER ºÄÄÄÄÙ º Voice VOICE º º User def 1 º º User def 2 º º User def 3 º º User def 4 º º User def 5 º º User def 6 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Modem message for Erroneous command This is the messages that your modem reports when any of the above events occurred during the operation of your modem. The above settings should be correct for any Hayes Compatible modem. If the above does not work for you, then you may adjust it to reflect the messages supported by your modem. Consult your modem manual, documentation or manufacturer for more info. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Command strings »Ä¿ º º ³ º Escape code +++ º ³ º Return on-line ~ATO| º ³ º Onhook ATH0| º ³ º Offhook ~ATM0H1| º ³ º Dial ATDT º ³ º ÃÄPrefix º ³ º ÀÄSuffix | ºÄÙ º Delay 5 º º Init-1 ATHZ| º º Init-2 º º Init-3 º º Down ATH1| º º Reset ATZ| º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ This is the sub-menu where you will define all your modem command strings. If you have Practical Peripherals or Hayes compatible, my above settings may work for you also. If the above stings does not work for you, then you can enter all the init strings from your BBS here as in Wildcat!. The only options that need edited is probably Init-1, Init-2, and Init-3. If you normally writes/saves your Init strings to your modem NVRAM, then all you need is Init-1 which should be ATHZ|, but if you did not write/save your Init strings to your modem NVRAM, just leave the Init-1 as ATHZ| and then put your normal Init strings in Init-2 and Init-3 as seen above. The begin- ing of each Init-2 or Init-3 should always begin with AT as written in the above setup. If you are lucky to be using Practical Peripherals PM14400FXSA or any Practical Peripherals modem, the above does not require any editing and should work fine, because I have the exact modem for my setup. Note: If you have chosen the right modem while installing Intermail, then some settings should have already been written to the lines of Init-1, Init-2, Init-3, whichever line is needed. Below is what I use successfully for my Practical Peripherals FXSA 14.4k modem at the time this documentation is written. Init-1: ATHZ| Init-2: AT&Q9E0M0L0V1&C1&D2S0=0X4S95=3S7=70| Init-3: ATS2=255S11=50&G2W2| If you are writing all your modem inits strings into your modem NVRAM, you can just eliminate Init-2 and Init-3 lines and just use only Init-1. Note: The more lines of Inits you use the more OK message you will get when you bring up InterMail, example: If you have Inits strings in Init-1 you get one OK message. If you have Inits strings in Init-1 and Init-2 you get two OK messages. If you have Inits strings in Init-1, Init-2 and Init-3 you get three OK messages. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍ Answer control »ÄÄÄÄ¿ º º ³ º Manual answer Yes º ³ º Force answer ATA| º ³ º Answer delay 5 º ³ º Answer on ring 1 º ³ º º ³ ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ If enabled, InterMail will answer the modem when a RING is received The sub-menu above should always be left as seen above. Please do not modify. If you modify it, your IM Mailer may not answer your phone for connection. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Connect strings » º # Connect Message Speed EC BBSexit Terminate º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º 1 CONNECT| 300 Y 0 0 º º 2 CONNECT 1200| 1200 Y 200 0 º º 3 CONNECT 1200/ 1200 Y 200 0 º º 4 CONNECT 1275 1200 Y 200 0 º º 5 CONNECT 7512 1200 Y 200 0 º º 6 CONNECT 2400| 2400 Y 200 0 º º 7 CONNECT 2400/ 2400 Y 200 0 º º 8 CONNECT 4800 4800 Y 200 0 º º 9 CONNECT 7200 7200 Y 200 0 º º 10 CONNECT 9600 9600 Y 200 0 º º 11 CONNECT 12000 12000 Y 200 0 º º 12 CONNECT 14400 14400 Y 200 0 º º 13 CONNECT 19200 19200 Y 200 0 º º 14 CONNECT 21600 21600 Y 200 0 º º 15 CONNECT 24000 24000 Y 200 0 º º 16 CONNECT 26400 26400 Y 200 0 º º 17 CONNECT 28800 28800 Y 200 0 º º 18 CONNECT 38400 38400 Y 200 0 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Enter-Edit Ins-Add Del-Del Esc-Exit F2-Error Correction In this sub-menu, you tell IM which errorlevel you want it to use when it exits on any human callers to your BBS. In our setup I have used errorlevel 200 for all BBS human caller (look at the CAT.BAT) and I have used 0 (zero) for 300 baud callers because I do not allow 300 baud to call my board, if you allow 300 baud callers to your board then change the 0 to 200 as others. You should leave all other errorlevels as they are, do not change them. This sub-menu is for the Connect Messages that your modem reports or issued to your modem whenever there is a connection to or from your modem. I personally use Practical Peripherals PM14400FXSA 14.4k External Modems and USR Robotics 28.8k on some nodes and I have locked my fossil at 38400 for all my modems and above is the message connections reported by my modems, yours may differ, the above should work for most modems and especially for all true Hayes and or especially for all true Hayes Compatible modems. If your modem issue different connect messages, then you should change or edit the above to the correct connect messages for your modem. But leave as above and experiment. But I think the above settings should work for most Hayes Compatible modems, leave the settings as above unless you have a problem with your mailer reporting the right connect messages. Note: All samples settings from this setup was used and based on my Practical Peripherals FXSA 14,400 Modem with the fossil locked at 38400. Note: You must set all the EC options to Y for YES for our baud rate translator to work, according to the author, Mr. Lawrence Gordon. Read FE2WC.DOC for more details. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍ»ÍÍÍÍÍÍÍÍÍÍÍÍ º Hardware º º Page º º Strings º º Xlat.Out º ÈÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ PRINTER ======= This is where you will define your printer setup. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍ Hardware »³ º º³ º Port LPT1 º³ º Baud rate 9600 º³ º Word length 7 ºÙ º Stop bits 1 º º Parity Even º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ This is where you specify which LPT or Parallel port your printer is connected and for normal operation, nothing else here should be changed except the Port option to specify your LPT or Parallel port for your printer. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÚÄÄÄÄÄÄÄÄÄÄ¿ÍÍÍÍÍÍÍÍÍÍÍÍ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Page control »³ º º³ º Paper forwarding Formfeeds º³ º Manual paper feed No º³ º Suppress ^a info Yes ºÙ º Page length 66 º º Page width 80 º º Left margin 5 º º Top margin 3 º º Bottom margin 3 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Page size, margins, etc. Leave the above options alone or you may change them to reflect the proper settings for your printer. This is not really important for our setup. Exit Global Mailer Editor Terminal Modem Printer Manager ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÉÍÍÍÍÍÍÍÍÍÍ»ÍÍ º Events º º Folders º º Security º º Requests º º Echomail º º Links º ÈÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ MANAGER SETUP: ============== This is one of the delicate, complicated and important area in our Intermail setup. I will try all my possible best to explain some things here to make sure you actually understand all the options, but if my explanation are not sufficient, please let me know or turn to others and seek help. This is where you will define all your Events or nightly maintenance that you normally run from inside your BBS (called External Event in IM), you will also define the events to poll (call) your HUB to pickup your FidoNet echomails (called Internal Events in IM). You can have as many events as you want here and for anytime of the day or night. I have enclosed 4 (four) sample events in this setup, the first event called Global event with @ Tag is necessary for IM to run, it must never be under any circumstances be deleted, if you delete it your IM will never run or operate. You will also define the security (Secured Password) for all the Mailers who will be calling you or whom you will be calling for echomail (not Netmail) with their Mailers. Example is also included in this setup. This Security setup is only necessary if you will be picking up FidoNet echomail from your HUB, and or if you will be acting as a HUB too. In this area setup, only Events and Security is really needed for our IM setup. All other options are not included and not required in this our setup. Please ignore or leave them alone. Now highlight Events and press Enter key for the next sub-menu screen. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Event manager » º # T Days M Start Length Min/Lev Max Address º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º 0 @ -------A * 00:00 24:00 0 0 1:278/9999 º º 1 X -------A * 01:00 00:01 70 -1 1:278/9999 º º 2 A -------A * 03:00 01:00 255 -1 1:278/9999 º º 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 º º º º º º º º º º º º º º º º º º º º º º º º º º º º º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Enter-Edit Space-More Ins-Add Del-Delete Esc-Exit Alt-C-Comments EVENTS: ======= This is the main Events definition screen. You will see the 4 (four) sample events I have defined for you above. You can disable any of the events, but the first event with Tag @ should or can never be disabled. Event can be disabled by highlighting Behavior and pressing enter key and set Inactive to YES make it Inactive, and reverse procedure to make it Active again. You can also delete any event and re-create it again as you wish. Let's explain each event in details below: Event #0 - Tag @ : This is called Global or Default event and under no circumstances should this be deleted or disabled. You should not have to modify this and the default setup settings here should function properly for everyone. This is also called an Internal Event. Never delete or disable this event or your mailer will never work. Event #1 - Tag X : This is a sample External event that you can use to run any other external programs from outside of IM, which means IM has nothing to do with this except to look for the corresponding errorlevel to exit with and carry out the instructions for this errorlevel. This type of event can be used to run your daily or nightly BBS maintenance events, because once you start using your Mailer (IM), your BBS will no longer execute the events defined within it, so IM will from now be your event manager not your BBS software, you will need to move all your BBS events to this IM events and delete or disable all the ones defined inside your BBS software. All External events are always linked to your CAT.BAT with a specified errorlevel line and the corresponding label for the errorlevel. Tag X must always be used for External Events. Please refer to your CAT.BAT for sample errorlevels. Event #2 - Tag A : This is a sample event to poll your FidoNet HUB for echomail. You should setup all your event for polling your HUB for mail this way, and this event is called Internal event and linked with your ROUTE.IM in your C:\IM\SYSTEM directory. You can use any Tag number from A-Z for any type of Internal event like this except Tag @ for Global and Tag X which is used for all External Events. Event #3 - Tag Z : This is called Zone Mail Hour (ZMH) and it's required for all mailer and BBS that has a Fidonet Network Node address. You should not delete this event. The event is setup so that your Mailer will not and should not accept any Human Caller at this event for its duration of one (1) hour. The sample setup settings enclosed here is fine for ALL. Note: You should inquire for the Start time of ZMH hour in your own area, based on your time clock. I have used 4am here because ZMH is 4am in New York or Eastern Std Time when this document was written, change the time to reflect your area ZMH hour. See POLICY4.TXT file included with this archive for the Zone Mail Hour (ZMH) in your area. General Warning about Events: You should not and cannot use the same Start Time for two or more events, there should always be at least one (1) minute difference between the Events. Example: If a first event starts at 04:00, the second event cannot start with the exact time instead it should start at 04:01. Intermail will not execute or run your events if two events has the same Start Time. Please be warned. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:00 255 -1 1:278/9999 ³ ³ 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 ³ ³ ³ ³ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Edit » º Tag @ º º Days -------A º º Modifier Ignore eventbase (*) º º Start time 00:00 º º Length 24:00 º º Min.cost 0 º º Max.cost 0 º º Behavior º º Use alias 1:278/9999 º º Retry delay 0 º º Comment Event base/default event º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º Event tag A..YZ - eXternal event, errorlevel is required º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ When you highlight Event #0 with Tag @ and press enter key, you will get this sub-menu screen. Use this sample and DO NOT modify this event. it has been setup correctly for you to use. Now highlight BEHAVIOR and press enter key, and you will get the following screen that defines the characteristics of this particular event. This event is linked with your ROUTE.IM in your C:\IM\SYSTEM directory, look for the line that says: "Schedule @ ALL" but please do not change anything in it, adjust your own settings as you have seen them. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:0ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Behavior » ³ 3 Z -------A * 04:00 01:0º Allow users during event Yes º ³ º Exit when mail is received Yes º ³ º High priority (crash) mail only No º ³ º Allow file requests Yes º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ Pickup file requests Yes º ³ Tag @ º Hold (don't send) file requests No º ³ Days -------A º Hold (don't send) file attaches No º ³ Modifier Ignore eventbase (*) º Attempt to pickup waiting mail Yes º ³ Start time 00:00 º Allow nodes to pickup waiting mail Yes º ³ Length 24:00 º Send-only No º ³ Min.cost 0 º Receive-only No º ³ Max.cost 0 º End event when no more mail to send No º ³ Behavior º Send to CM systems only No º ³ Use alias 1:278/9999 º Send to non-CM systems only No º ³ Retry delay 0 º Only execute event once No º ³ Comment Event base/default evº Inactive No º ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Miscellaneous options Space-Toggle ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ This screen will pop-up when you highlight Behavior and press enter key from the previous menu. This option settings should not be modified, leave them the way they are, because they have been defined properly, just look at them for curiosity sake, when finished looking, please, press ESC key to return to the previous menu, then another Esc key to go back to the Main Event Menu, so we may analyze or take a look at the other event's Behavior. Note: This Global or Default is very important and mandatory or compulsory for you to have before your mailer will operate. So do not delete or modify it. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:00 255 -1 1:278/9999 ³ ³ 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 ³ ³ ³ ³ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Edit » º Tag X º º Days -------A º º Modifier Ignore eventbase (*) º º Start time 01:00 º º Length 00:01 º º Errorlevel 70 º º Not used º º Behavior º º Use alias 1:278/9999 º º Retry delay 0 º º Comment External Event to Run my BBS Events º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º Event tag A..YZ - eXternal event, errorlevel is required º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ This is a sample External Event that can be used for any purpose like running your BBS daily or nightly events that you would normally run from inside your BBS software. IM will not execute all the events you define in your BBS software, so you will need to move all of those events to IM to manage for you. The external events are always and must always be linked with to your CAT.BAT and it's corresponding defined errorlevel and the label for the errorlevel. Please take a look in your CAT.BAT for the line that says "IF ERRORLEVEL 70 goto ..." and edit to suit the program you want to run, one of this event and errorlevel can run several programs at the same time thru your batch file(s). You can also create as many of this type of event as you need for your BBS maintenance and they should all have the Tag X as their TAG but they can have different errorlevel and or different Start Time to do whatever you want or to call another batch file(s) to be executed. NOTE: ALL EXTERNAL EVENT MUST AND SHOULD ALWAYS USE TAG X AND THE LENGTH MUST ALWAYS BE 00:01 and MUST HAVE THE CORRESPONDING DEFINED ERRORLEVEL LINE IN YOUR CAT.BAT. Now highlight Behavior and press your enter key to see how this and all other External Events will and should behave in next screen. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:00 255 -1 1:278/9999 ³ ³ 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 ³ ³ ³ ³ ³ ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Tag X ³ ³ Days -------A ³ ³ Modifier Ignore eventbase (*) ³ ³ Start time 01:00 ³ ³ Length 00:01 ³ ³ Errorlevel 70 ³ ³ Not used ³ ³ Behavior ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Behavior » ³ Use alias 1:278/9999 º Allow users during event No º ³ Retry delay 0 º Forced Yes º ³ Comment External Event to Run my BBS Eventº Inactive No º ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Miscellaneous options Space-Toggle ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ For External Events Behavior, nothing much to do here. Only three options: 1: The first option is either to Allow Users during this event or not. If you want your event to execute at the exact time, you should not allow user during this event, this is how I have all mine defined. 2: Forced means, should this event still execute or not if it was missed due to some reason, (e.g board crash, etc)? You should probably set this to YES like mine to make sure you never missed any event, in case your board crash before the event runs. 3: Inactive means, this is to disable the event if you do not need it for a particular period. This will disabled or enable the event when you want. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:00 255 -1 1:278/9999 ³ ³ 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 ³ ³ ³ ³ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Edit » º Tag A º º Days -------A º º Modifier Ignore eventbase (*) º º Start time 03:00 º º Length 01:00 º º Min.cost 255 º º Max.cost -1 º º Behavior º º Use alias 1:278/9999 º º Retry delay 0 º º Comment Event to Poll my HUB for Echomails º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º Event tag A..YZ - eXternal event, errorlevel is required º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ This is a sample Event to be used for polling (call) your HUB when you are linked and ready for your FidoNet echomails, when the Mailer (IM) finished receiving the mails, it will exit with Errorlevel 255 that has been defined in your CAT.BAT to process your mail with your mail tosser. You should only have to change the start time you want this event to occur. You should also create more of this type of events for all other HUBs you call for mails and their corresponding Start Time, and you should also use the same errorlevel 255 for all of them. You should use different Tag letter from A-Z for each event you define, except Tag @ which is only for Global and also except Tag X which is also reserved for external events. Any event that polls your HUB for mails is called Internal Event processed directly by IM. This event is also linked with your ROUTE.IM in C:\IM\SYSTEM directory, look for the the line that says: Schedule A 1:278/1000 please replace the address with your own HUB address. Now highlight Behavior and press enter key for next screen to see how this event will behave, adjust your settings as you see them here. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:0ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Behavior » ³ 3 Z -------A * 04:00 01:0º Allow users during event Yes º ³ º Exit when mail is received Yes º ³ º High priority (crash) mail only No º ³ º Allow file requests Yes º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ Pickup file requests Yes º ³ Tag A º Hold (don't send) file requests No º ³ Days -------A º Hold (don't send) file attaches No º ³ Modifier Ignore eventbase (*) º Attempt to pickup waiting mail Yes º ³ Start time 03:00 º Allow nodes to pickup waiting mail Yes º ³ Length 01:00 º Send-only No º ³ Min.cost 255 º Receive-only No º ³ Max.cost -1 º End event when no more mail to send No º ³ Behavior º Send to CM systems only No º ³ Use alias 1:278/9999 º Send to non-CM systems only No º ³ Retry delay 0 º Only execute event once No º ³ Comment Event to Poll my HUB º Inactive No º ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Miscellaneous options Space-Toggle ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ This is how the event to poll your HUB will behave, and under normal circumstances the settings above should not need any modification except the Start Time of the Event. As you can see above that this event will be trying to call your HUB for one hour when until connection is made, if the connection with the HUB is not made, IM will allow any human caller that calls your BBS and it will resume calling the HUB as soon as the caller log-off your board if the time is still within the one hour range, controlled by Length of 01:00 above. if you do not want any caller allowed within this one hour duration, then you can set the first option "Allow Users During Event" to NO. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:00 255 -1 1:278/9999 ³ ³ 3 Z -------A * 04:00 01:00 0 -1 1:278/9999 ³ ³ ³ ³ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Edit » º Tag Z º º Days -------A º º Modifier Ignore eventbase (*) º º Start time 04:00 º º Length 01:00 º º Min.cost 0 º º Max.cost -1 º º Behavior º º Use alias 1:278/9999 º º Retry delay 0 º º Comment Zone Mail Hour (ZMH) Based on Region º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º Event tag A..YZ - eXternal event, errorlevel is required º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ When you highlight Event #3 with Tag Z and press enter key, you will get this sub-menu screen. This is for Zone Mail Hour (ZMH) as described previously. The only thing you should change here is the Start time for the Zone Mail Hour for your area. (Ask other Fidonet Sysops around your area for the ZMH). This event is a requirement from the FidoNet Organization and should lasts for 1 (one) hour and that is why you see the option "Length 01:00" which means this event will last for one hour. This is a requirement for all FidoNet Members and should be observed and not deleted or disabled once you get your FidoNet Node address from your area NC. Now highlight Behavior and press enter key to see the behavior characteristics of this event, please do not modify it, the options settings are fine for all occasion. Next screen is the Behavior. Note: Look in the enclosed POLICY4.TXT by FidoNet Organizations enclosed with this archive to determine the Zone Mail Hour (ZMH) Start Time for your area. The length for this event should and MUST always be for One (1) hour in duration as seen above. You can and will be thrown-out (ex-communicate) from FidoNet if you do not observe this Zone Mail Hour. This is very important, be warned. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ # T Days M Start Length Min/Lev Max Address ³ ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij ³ 0 @ -------A * 00:00 24:00 0 0 1:278/9999 ³ ³ 1 X -------A * 01:00 00:01 70 -1 1:278/9999 ³ ³ 2 A -------A * 03:00 01:0ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Behavior » ³ 3 Z -------A * 04:00 01:0º Allow users during event No º ³ º Exit when mail is received Yes º ³ º High priority (crash) mail only No º ³ º Allow file requests No º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ Pickup file requests No º ³ Tag Z º Hold (don't send) file requests No º ³ Days -------A º Hold (don't send) file attaches Yes º ³ Modifier Ignore eventbase (*) º Attempt to pickup waiting mail Yes º ³ Start time 04:00 º Allow nodes to pickup waiting mail Yes º ³ Length 01:00 º Send-only No º ³ Min.cost 0 º Receive-only No º ³ Max.cost -1 º End event when no more mail to send No º ³ Behavior º Send to CM systems only No º ³ Use alias 1:278/9999 º Send to non-CM systems only No º ³ Retry delay 0 º Only execute event once No º ³ Comment Zone Mail Hour (ZMH) º Inactive No º ³ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ Miscellaneous options Space-Toggle ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ This is how the Zone Mail Hour (ZMH) event will behave. All the options has been setup correctly and does not need any modifications. As you can see in the above settings, for the one hour duration of this event, your Mailer (IM) will not allow any Human Caller to access your BBS, only another Mailer can connect to your board for Netmail purposes only, no file transfer or echomail pick-up during this event. This is the requirements by FidoNet Organizations for all FidoNet Members, and should be observed. THERE IS NO EXCEPTIONS TO THE ABOVE REQUIREMENT, unless you are not a FidoNet Node. Remember, you can be cut-off from FidoNet for not observing the ZMH Hour. If you are not a member of Fidonet Organization or does not have a Fidonet Node address or you do not intend to be, then you can disable this event by highlighting the option "Inactive" and press Space bar to toggle it to YES, and that will disable the event until re-enabled again thru the same procedure. This event is linked to ROUTE.IM in your C:\IM\SYSTEM directory. Look for the line that says: Schedule Z ALL please do not change anything there, just look. Now Esc back to the Event Menu and let's look at the other Events and their respective Behaviors settings. Adjust your settings as seen above. Now press Esc and return to the Manager Screen, we shall now complete our last settings in IM. Please highlight SECURITY from the Manager menu and press enter key for the following screen. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Security manager » º # System Password FREQs º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º 1 1:278/1000 PASSWORD Yes º º º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ Mail server: 001 ÃÄ Enter-Edit F1-Inactive F2-FREQs Ins-Add Del-Delete Esc-Exit This is the Security Definition Menu. This is where you will define the HUB/Node Address and Password for the HUB system you will be calling for echomail. If you are not calling (polling) for echomail yet, you can just leave this alone or delete it. If you are also a HUB for some echomail, you will need to enter all the Node Address of all the people who will be calling your system to pick-up their echomails. Please change the Number under System to your HUB Node Address Number and replace the PASSWORD with the Password he has assigned to you for polling him, or you can just delete the whole thing and setup yours when you are ready for polling echomail. Make sure all the other option setting read YES for the FREQs as seen above for better connection to your HUB. Press Esc key and return to the opening screen and press Esc key again and answer Y for YES to save all your settings in our Intermail setup. Now you can take a breather, because this is our last settings in Intermail. The next page will show you how to compile your Nodelist, and your Mailer (IM) should be ready to roll. I hope you have enjoyed this settings. Final Setup or Completion or Intermail and Related Utilities. ============================================================= Here we shall Compile our Nodelist for Intermail and Wildcat!. Make sure you have the following files in the stipulated directories: 1: In C:\IM you should have the following files: EDITNL.EXE -> Executable file to merge our weekly Nodediff with Nodelist. BANNER.TXT -> Edit to suit your system with a ascii text editor EVENT.TXT -> Edit to suit your system with a ascii text editor MAGIC.LST -> File that list directories to your files areas. EXEBBS.BAT -> File that transfers Intermail to Wildcat! BBS FAILED.TXT -> File sent to other Mailer for failed file request (FREQ) CAT.BAT -> Batch that will invoke IM and then pass callers to Wildcat! FE2WC.EXE -> Baud and error correction translator for IM and WC!4.x FE2WCT.EXE -> Same as above for use with OS/2 with /T switch hardcoded. 2. In C:\IM\SYSTEM you should have the following files: ROUTE.IM -> Edit with a ascii text editor and replace all the addresses. 3: In C:\IM\NODELIST you should have the following files: FDNODE.CTL -> Edit this file and replace the three digit of phone number. NODELIST.??? -> Current Nodelist obtained from your NC. 4: Now change to your Nodelist directory i.e. C:\IM to compile your Nodelist. While still in C:\IM type IMNC /F when this procedure is completed, Intermail should have successfully compiled your Nodelist for it's use. 5: Whenever you poll your NC for the weekly NODEDIFF.A??, the CAT.BAT should do the above for you automatically, but if for any reason you need to process this manually, I have included a file called NODEDIFF.BAT to do this for you, please edit this file for the correct path. You must process your Nodediff every week for your Nodelist to be current. 6: After you receive your own actual Node Address from your area Network Co-Ordinator (NC), you must repeat step 4 and 5 to recompile your Nodelist. Note: After the whole setup is completed, you can finally bring up your Intermail with the supplied CAT.BAT that should be in your Intermail directory, i.e. C:\IM, and if your Intermail comes up successfully, press F1 function key to logon locally and if everything went fine, your mail tosser should scan your sample message conference when you log off your board. Remember to load your Fossil driver before you attempt to bring up Intermail if you want to use a fossil driver. Although Intermail will run without loading a fossil driver, but it does enhance the operation of Intermail when fossil is loaded. Enjoy your FidoNet trip. If everything went well, you should see something similar to the next screen as InterMail loads. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ InterMail 2.29 - Node 1:278/9999 #1 Sun 01 Jan 95 11:11 AM ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ³ ³ ³ ³ ³ ³ + SIO driver: X00 V1.50 ³ ³ ³ Mail Server ID#: 001 ³ ³ ³ + Event 0-@ ³ ³ ³ Checking message base ³ ³ ³ Using: ROUTE.IM ³ ³ ³ : #1 to 1:0/0: disqualified, forwarding not accepted ³ ³ ³ - Preparing outbound mail ³ ³ ³ No messages to send in this event ³ ³ ³ Initializing the modem ³ OK ³ ³ Waiting for a call or event ³ OK ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ³ Event 0 @ 23:59 ³ ³ ³ ³ ³ ³ Next 1 X 1:00 ³ ³ ³ (Mon) ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ Press F10 for menu ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Remember to send me a "Thank You" Netmail at 1:278/111. And any suggestions to enhance this documentation can also be sent to me at the above Fido address. Thank you. ---- end ---- God Bless. Praise be to Allah.