ÚÂÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
                            ³³³  INSTALLATION  ³³³
                            ÀÁÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÁÙ

         System Requirements.........................................1
         Users With a Hard Disk Drive................................2
         Users With One 3.5" Disk Drive (No Hard Disk)...............3
         Users With 1 HD 5.25" Disk Drive (No Hard Disk).............4
         Users With One 360K (DD) 5.25" Drive (No Hard Disk).........5
         Users With 2 Floppy Disk Drives (No Hard Disk)..............6
         Running the Program.........................................7


    For help on running TOTAL RECALL print the HELP.TXT file.  For more 
    information on TOTAL RECALL print the README.TXT file.   To Register 
    TOTAL RECALL print the ORDER.TXT file and use it as a blank order form.


    1.    System Requirements
    =========================

    To run TOTAL RECALL all you need is an IBM compatible computer, 640K of 
    memory, 1 or 2 floppy drives high density drives (hard disk recommended 
    but not necessary), any kind of monitor or video card, and MS-DOS 2.0 or 
    later.

    If you wish to use PCX picture files with your entries you will almost 
    have to have a hard disk due to the large size of most graphics files.

    1) (You may not need to perform this first step unless you wish to 
       optimize your system performance or have DOS 3.2 or earlier).  You 
       should have a file called CONFIG.SYS in your top-level directory (or 
       on the system disk from which you boot-up if you don't have a hard 
       drive).  Edit the file CONFIG.SYS and add the following two 
       statements to it:

                FILES=20
                BUFFERS=8

       If you don't have a CONFIG.SYS file in your top-level directory, copy 
       the one included with the TOTAL RECALL disk.


    2) Make sure that the file COMMAND.COM is in the DOS path or in the top
       directory.

    3) If you use memory resident programs or TSRs you may have problems
       running TOTAL RECALL due to its large memory requirements or other
       conflicts.   If so, do not load any memory resident programs at
       boot-up.


    2.    Users With a Hard Disk Drive
    ==================================

    1) Create a working directory, get into that directory, and copy all 
       TOTAL RECALL files from the distribution disk to that directory as 
       follows:

                C:
                CD\
                MD RECALL
                CD RECALL
                COPY A:*.*

    2) Run the program by typing:

                TR3


    Note: The GO TO DOS option will not work unless you have a system disk
    in the default path.


    3.    Users With One 3.5" Disk Drive (No Hard Disk)
    ===================================================

    Copy the contents of the distribution disk to a working disk and then do 
    your work entirely from that disk without any further disk swapping.

    1) Place the original distribution (source) disk in drive A: (or B:).
    2) Type the following:

                DISKCOPY A: A:

    3) Swap your working (destination) disk as instructed.


    4.    Users With 1 HD 5.25" Disk Drive (No Hard Disk)
    =====================================================

    Follow the same instructions as for 1.3 above.


    5.    Users With One 360K (DD) 5.25" Drive (No Hard Disk)
    =========================================================

    You will not be able to run version 3.30 or later of TR on a system with 
    only a low density 5.25" drive and no hard disk.  You can call Zoft 
    Systems and request an earlier version.

    6.    Users With 2 (HD) Floppy Disk Drives (No Hard Disk)
    =========================================================

    Use drive A: to hold the main program TR.EXE and to use drive B: to hold 
    your SUBJECT FILES.

    1) Copy TR.EXE to a system disk.  (This is necessary in order for the GO 
       TO DOS option to work).  To create a system disk, format a disk with:

                FORMAT A:/S

    2) Copy TR.EXE to the newly created disk.
    3) Insert the new disk into drive A: and start to run by typing:

                A:\TR3

    4) Insert a blank formatted disk into drive B:
    5) Whenever the program asks you for a Path, type

                B:


    7.    Running the Program
    =========================

    1) Run the program by typing:

                TR3

    2) From here on everything is menu-driven and self-explanatory.   Make 
       menu selections by a) using arrow keys to move highlight bar to 
       choice and pressing RETURN or b) pressing the first letter of desired 
       choice.

    3) You can customize the colors and the sound from the CUSTOMIZE MENU.
       Your new set-up will be saved automatically to disk.


    Note the following:
    -------------------

    The following files must be in the same directory as the main TOTAL 
    RECALL program (TR.EXE) that you run or load from:

        TEST.LOG
        QUOTES.DAT
        CUSTOM3.MEM
        README.TXT
        HELP.TXT
        INSTALL.TXT
        SUBJECTS.TXT

    [Esc] means to press the key marked "Esc".  This will usually quit
    or exit whatever you are doing at the time.

    [^W] means press the key marked "Ctrl" together with the letter W.

       Copyright (c) 1988-1993 by Zoran Sevarlic.  All Rights Reserved.