Updates to: Installation Guide and Using the Operating System Document Number 82G6228-00 February 4, 1994 +--- Note -----------------------------------------------------------+ | | | Before using this information and the product it supports, be sure | | to read the general information under Appendix A, "Notices" on | | page 9. | | | +--------------------------------------------------------------------+ Contents ------------------------------------------------------------------------------ Part 1: Changes to OS/2 2.1 Installation Guide . . . . . . . . . . . . . ii About This Book . . . . . . . . . . . . . . . ii Before You Begin . . . . . . . . . . . . . . ii Chapter 1. Choosing an Installation Procedure ii Chapter 2. Installing OS/2 2.1 as the Only Operating System (Basic Installation) . . . ii Chapter 3. Adding OS/2 2.1 to a DOS System (Dual Boot) . . . . . . . . . . . . . . . . ii Chapter 4. Installing Multiple Operating Systems (Boot Manager) . . . . . . . . . . . ii Chapter 5. Using a Response File to Install ii Appendix A. Adding Features and Changing Your System Configuration . . . . . . . . . . . . ii Appendix B. Diagnosing System Problems . . . ii Appendix F. Migrating from OS/2 Extended Edition to OS/2 2.1 . . . . . . . . . . . . ii Appendix G. Upgrading the BIOS of Your Computer . . . . . . . . . . . . . . . . . . ii Appendix H. Notices . . . . . . . . . . . . ii ------------------------------------------------------------------------------ Part 2: Changes to OS/2 2.1 Using the Operating System . . . . . . . . . ii About This Book . . . . . . . . . . . . . . . ii New Features in OS/2 2.1 . . . . . . . . . . ii Chapter 1. Getting Started with OS/2 2.1 . . ii Chapter 4. System Setup . . . . . . . . . . 1 Power . . . . . . . . . . . . . . . . . . . 1 PCMCIA . . . . . . . . . . . . . . . . . . 5 Chapter 5. Startup . . . . . . . . . . . . . 5 Chapter 6. Drives . . . . . . . . . . . . . 5 Chapter 8. Productivity . . . . . . . . . . 6 Chapter 10. Information . . . . . . . . . . 6 Chapter 12. Drive A . . . . . . . . . . . . 6 Chapter 16. Printers and Plotters . . . . . 6 Chapter 17. Preparing Your Programs . . . . 6 Chapter 18. Using Windows Programs . . . . . 6 Chapter 23. Audio Support for Applications . 6 Part 5: Extra Help . . . . . . . . . . . . . 6 Chapter 24. Solving Problems . . . . . . . . 6 Chapter 26. Software Support . . . . . . . . 6 Chapter 27. Video Support . . . . . . . . . 6 Chapter 28. Printer Support . . . . . . . . 6 Chapter 29. Hardware Support . . . . . . . . 6 Appendix B. Error Messages . . . . . . . . . 8 Appendix C. Backing Up and Restoring Your Desktop . . . . . . . . . . . . . . . . . . 8 Appendix F. Removing Programs . . . . . . . 8 Appendix A. Notices . . . . . . . . . . . . 9 Trademarks and Service Marks . . . . . . . . 9 About This Booklet The purpose of this booklet is to provide you with updates to the OS/2 2.1 Installation Guide and the OS/2 2.1 Using the Operating System book. Keep this booklet as a reference and look here first before referring to the Guide or Using book. HOW TO USE THIS BOOKLET _______________________ This booklet should be used in conjunction with the Installation Guide and Using the Operating System book. Only chapters that have changes are listed in this booklet. All changes begin with a reference to the page in the original documentation on which the change is to be made. Note: Because some of these changes are lengthy, you might want to make a notation on the original page referring to the update located in this booklet. HOW THIS BOOKLET IS ORGANIZED _____________________________ This booklet is organized into the following parts: o Part 1 contains changes to the OS/2 2.1 Installation Guide. o Part 2 contains changes to the OS/2 2.1 Using the Operating System. CONVENTIONS USED IN THIS BOOKLET ________________________________ The following conventions are used in this booklet to help distinguish elements of the text: +---------------+--------------------------------+ | Text Element | Use | +---------------+--------------------------------+ | bold | Indicates the name of an item | | | you that you can select. | +---------------+--------------------------------+ | italics | Indicates the first time a new | | | term is used. A definition of | | | the term immediately follows | | | the italicized terms. Italics | | | are also used to indicate a | | | book title or variable | | | information that must be | | | replaced by an actual value. | +---------------+--------------------------------+ | monospace | Indicates an example such as a | | | fictitious path and file name | | | or text that is displayed on | | | your screen, such as an error. | +---------------+--------------------------------+ | UPPERCASE | Indicates a file name, command | | | name, or acronym. | +---------------+--------------------------------+ | * | Indicates trademarks of the | | | IBM Corporation. | +---------------+--------------------------------+ | ** | Indicates trademarks of other | | | companies. | +---------------+--------------------------------+ PART 1: CHANGES TO OS/2 2.1 INSTALLATION GUIDE Part 1 contains information that is new or different from the information in the OS/2 2.1 Installation Guide. The chapter numbers and titles in this booklet are the same as those used in the Installation Guide; only those chapters of the Guide that are changed are included here. ABOUT THIS BOOK _______________ > On page x, add the following entry to the list in the section titled "How This Book Is Organized": o Appendix H provides information on creating a startup diskette for OS/2(*) 2.1. Note: The original Appendix H, "Notices" is now Appendix I, "Notices". BEFORE YOU BEGIN ________________ > On page xiii, replace the second paragraph with the following: Late-breaking information about installation can be found in the README.INS file. This file is located on Diskette 3 of the diskette package and on Diskette 1 of the CD package. > On page xiii, add the following minimum requirement: o At least CGA video support. > Under the section titled "Questions About Your Current Computer System" on page xiv, add the following questions and answers: o Are you installing on an EISA system with an Adaptec(**) 1742A controller card? If you have an EISA system with an Adaptec 1742A controller card and you want to install OS/2 2.1, you must run the Setup Configuration program provided on the Adaptec Card Setup Diskette. To set up the Adaptec card in the configuration using the Setup Diskette, do the following: 1. Set the Enhanced mode setting to OFF. 2. Set the Standard mode setting to ON. 3. Set the Hex Address setting to C800. 4. Set the I/O Port setting to 230H. 5. Set the DMA channel setting to 5. 6. Set the Parity Check setting to OFF. 7. Set the Synchronous Negotiation setting to ON. If CD-ROM is not recognized, set this setting to OFF. 8. Set the Enabled Disconnect setting to YES. 9. Set the IRQ setting to 11 (default is 2). o Are you installing OS/2 2.1 on an IBM(*) ThinkPad(*) with a Docking Station(**)? If you are installing OS/2 2.1 on an IBM ThinkPad 700, 700C, 720, or 720C attached to a 3550 Docking Station, you need to replace the ABIOS files on the OS/2 Installation Diskette with files from the Reference Diskette. Do the following: 1. Detach the ThinkPad from the Docking Station. 2. Create a Reference Diskette by following the documentation that came with the ThinkPad. 3. Make a copy of the Installation Diskette. 4. Remove the copy and insert the original Installation Diskette into drive A. 5. Turn on the computer. If it is already on, press and hold Ctrl+Alt and press Del to restart the system. 6. When you are prompted to do so, remove the Installation Diskette, insert Diskette 1, and press Enter. 7. When the Welcome screen is displayed, press Esc to display the command prompt. 8. Insert the copy of the Installation Diskette into drive A. 9. Type: A:\DEL *.BIO and press Enter. 10. Remove the copy of the Installation Diskette, and insert the Reference Diskette you created in step 2 into drive A. 11. If your computer has more than one diskette drive, insert the copy of the Installation Diskette into drive B. In the next two steps, you will be prompted to insert diskettes into both drive A and drive B. If your computer has only one diskette drive, when you are asked to insert a diskette into drive A, insert the Reference Diskette into your diskette drive. When you are asked to insert a diskette into drive B, insert the copy of the Installation Diskette into your diskette drive. 12. Type: COPY A:\*.BIO B:\ and press Enter. 13. Type: COPY A:\ABIOS.SYS B:\ and press Enter. 14. Turn off the ThinkPad and return it to the Docking Station. 15. Restart the installation procedure by inserting the copy of the Installation Diskette into drive A. o Are you installing on a system with an AOX upgrade? If you have a system with a 286 processor that has been upgraded to a 386SX with an AOX upgrade and you want to install OS/2 2.1, you must start the system with DOS and run the AOX232.EXE. To request the AOX232.EXE, contact the AOX Technical Support Group at 1-800-232-1269. > On page xv, add the following note after the question "Is your display adapter an ATI(**) Graphics Ultra(**) Pro?": Note: If you have a Gateway 2000(**) system, refer to "Black Lines on an OS/2 Logo Screen" for further instructions. > On page xvii, add the following header before the third paragraph: SCSI-Based CD-ROM Support > On page xvii, add the following section to the end of the page: Non-SCSI CD-ROM Support for Sony, Panasonic, and Mitsumi For the Sony(**), Panasonic(**), and Mitsumi(**) non-SCSI drives to be recognized by OS/2, the base port address specified on the CD-ROM BASEDEV statement in CONFIG.SYS must match the base I/O port address specified on the CD-ROM host adapter card. Note: If you are installing OS/2 2.1 from a CD-ROM, you might first need to modify the BASEDEV statement for your CD-ROM device driver in the CONFIG.SYS file on the diskette labeled Diskette 1. Modifying CONFIG.SYS for the Sony CDU-31A Device Driver: The examples that follow illustrate how this CD-ROM is attached to the most common host adapters and indicate the required parameter switch settings for each CD-ROM drive. Example 1: The Sony CDU-31A CD-ROM drive is attached to a Sony CDB-334 host adapter. The Sony CDB-334 host adapter supports base I/O port addresses of 320h, 330h, 340h, or 360h. If the host adapter is set to its default port address of 340h, the CONFIG.SYS statement does not need to be modified and should appear as follows: BASEDEV=SONY31A.ADD If the CDB-334 host adapter is set to any port address other than the default of 340h, the CONFIG.SYS statement must be modified. For example, if the Sony CDB-334 host adapter is set to a base I/O port address of 360, the line in the CONFIG.SYS file should appear as follows: BASEDEV=SONY31A.ADD /A:0 /P:0360 Example 2: The Sony CDU-31A CD-ROM drive is attached to a Media Vision(**) ProAudio Spectrum(**) 16 host adapter. In this case, the line in CONFIG.SYS must be modified and should appear as follows: BASEDEV=SONY31A.ADD /A:0 /AT:08 Example 3: The Sony CDU-31A CD-ROM drive is attached to a Creative Labs Sound Blaster(**) Pro, Sound Blaster 16, or Sound Blaster 16 MultiCD host adapter. The port address specified on the BASEDEV statement in CONFIG.SYS should be 10h above the base I/O port address specified on these adapter cards. For example, if the Sound Blaster card is set for a base I/O port address of 220h, the line in CONFIG.SYS should appear as follows: BASEDEV=SONY31A.ADD /A:0 /P:0230 Modifying CONFIG.SYS for the Panasonic Device Driver: The Panasonic device driver (SBCD2.ADD) supports the following CD-ROM drives: - Panasonic CR-521,522,523,562,563 - Creative Labs OmniCD - IBM ISA CD-ROM drive The examples that follow illustrate how this CD-ROM is attached to the most common host adapters and indicate the required parameter switch settings for each CD-ROM drive. Example 1: A Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive is attached to a standard Panasonic or IBM CD-ROM host adapter. The standard Panasonic or IBM host adapter supports base I/O port addresses of 300h, 310h, 320h or 330h. For example, if the adapter is set to a base I/O port address of 300, the line in the CONFIG.SYS file should appear as follows: BASEDEV=SBCD2.ADD /P:300 Example 2: A Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive is attached to a Creative Labs Sound Blaster Pro, Sound Blaster 16, or Sound Blaster 16 MultiCD. If the Sound Blaster card is set for a base I/O address of 220h, the line in CONFIG.SYS should appear as follows: BASEDEV=SBCD2.ADD /P:220 Example 3: A Creative Labs OmniCD is attached to a standard Creative Labs CD-ROM host adapter. The standard Creative Labs host adapter supports base I/O port addresses of 250h or 260h. For example, if the adapter is set to a base I/O port address of 250, the line in the CONFIG.SYS file should appear as follows: BASEDEV=SBCD2.ADD /P:250 /T:2 Modifying CONFIG.SYS for the Mitsumi CD-ROM Device Driver: The examples that follow illustrate how this CD-ROM is attached to the most common host adapters and indicate the required parameter switch settings for each CD-ROM drive. Example 1: A Mitsumi CD-ROM drive is attached to a Mitsumi host adapter. The Mitsumi host adapter supports I/O port address ranges from 300h to 3FCh. If the Mitsumi host adapter is set to a base I/O port address of either 300h or 340h, the statement in CONFIG.SYS does not need to be modified and should appear as follows: BASEDEV=MITFX001.ADD If the Mitsumi host adapter is set to an address other than those specified above, the BASEDEV statement needs to be modified. For example, if the Mitsumi host adapter is set to a base I/O port address of 320, the line in the CONFIG.SYS file should appear as follows: BASEDEV=MITFX001.ADD /P:320 Example 2: A Mitsumi CD-ROM drive is attached to a Creative Labs Sound Blaster 16 MultiCD. If the Mitsumi CD-ROM port on the Sound Blaster 16 MultiCD is set to an I/O port address of 320, the line in CONFIG.SYS should appear as follows: BASEDEV=MITFX001.ADD /P:320 > On page xviii, add the following note before the second paragraph: Note: Use the LOADDSKF utility program to create diskette images, which are compressed, binary images of a diskette. The LOADDSKF.EXE is in the \DISKIMGS directory of the CD. LOADDSKF can be run from either the DOS or OS/2 operating system. > On page xix, add the following additional note to the section titled "Additional Notes for Users of OS/2": o To avoid desktop problems such as a blank desktop or duplicated icons, you need to run CHKDSK /F and have at least 20MB of free space in your OS/2 partition. CHAPTER 1. CHOOSING AN INSTALLATION PROCEDURE ______________________________________________ > On page 6, replace paragraph 3 with the following: The amount of space you need for the OS/2 2.1 partition depends upon which features of the operating system you are going to install. The amount of space required is also related to how much system memory your computer has and how many applications will be running at the same time. If you are going to install all features of the operating system, you need approximately 40MB of free disk space and a minimum of 10MB of space for the SWAPPER.DAT file. If you are going to install selected features, you need from 20MB to 40MB. These installation choices are described in more detail in Chapter 2, "Installing OS/2 2.1 as the Only Operating System (Basic Installation)". If you are going to install multimedia support, you need up to an additional 5MB of hard disk space. CHAPTER 2. INSTALLING OS/2 2.1 AS THE ONLY ___________________________________________ OPERATING SYSTEM (BASIC INSTALLATION) _____________________________________ > On page 16, replace the first 3 paragraphs with the following: Install preselected features If you select this predetermined set of OS/2 features, you will need approximately 32MB of total disk space for the operating system and its features and a minimum of 10MB for the swapper file. Install all features If you select all features, you will need approximately 40MB of total disk space for the operating system and its features and a minimum of 10MB for the swapper file. Select features and install If you decide to select the features you want to install, you need from 20MB to 40MB of total disk space for the operating system and its features and a minimum of 10MB for the swapper file. > On page 24, add the following paragraph before the sentence "To make a selection different from the one listed in this window...": For non-SCSI CD-ROM drives, if you cannot access your CD-ROM device after installation, ensure that the port address in the BASEDEV statement in the CONFIG.SYS file on your startup partition (hard drive) matches the port address on the CD-ROM host adapter card. See "Non-SCSI CD-ROM Support for Sony, Panasonic, and Mitsumi". > On page 33, replace the second paragraph of the second list entry with the following: When the Update Windows desktop when WIN-OS/2 desktop is modified option is selected during the installation, the WIN-OS/2(*) PROGMAN.INI file points to the Microsoft(**) Windows(**) group files. However, WIN-OS/2 does not use the Microsoft Windows PROGMAN.INI file. Two different PROGMAN.INI files exist and each one is maintained by the respective system (OS/2 or Windows). Because both desktops share group files, they will reflect the changes when an existing group of files is modified. However, if a modification to the PROGMAN.INI file is necessary (add/remove a group file), the desktops will differ. New groups will not be reflected on the Microsoft Windows desktop. CHAPTER 3. ADDING OS/2 2.1 TO A DOS SYSTEM (DUAL _________________________________________________ BOOT) _____ > On page 37, add the following warning after the first paragraph: Warning: While it is possible to install OS/2 2.1 and DOS in the same partition, you might experience problems during the installation. To avoid these problems, use Boot Manager instead of Dual Boot. Refer to Chapter 4, "Installing Multiple Operation Systems (Boot Manager)" for more information. > On page 48, replace the boxed note with the following: +--- What to Do if Dual Boot Does Not Work --+ | | | If the BOOT command is unsuccessful when | | you try to switch from DOS to OS/2 2.1, | | you might have one or more active | | terminate-and-stay-resident (TSR) or DOS | | cache programs. If so, end the programs | | before you use the BOOT command. For TSR | | programs that are loaded from | | AUTOEXEC.BAT, you must deactivate the | | programs before using the BOOT command. | | | +--------------------------------------------+ CHAPTER 4. INSTALLING MULTIPLE OPERATING SYSTEMS _________________________________________________ (BOOT MANAGER) ______________ > On page 50, add the following note after the first paragraph: Note: If you have a system with a VESA(**) SUPER I/O controller and two disk drives, the system will not start DOS from the Boot Manager menu. Instead, it will display a non-system disk or disk error message. For more information on this message, check the VESA controller documentation or contact the manufacturer. > On page 52, add the following note after the third paragraph: Note: If a partition is going to contain an operating system, the partition cannot be larger than 1 GB (gigabyte) or 1024 cylinders. > On page 70, replace the table entry for OS/2 2.1 with the following: +----------+------------+------------------------+ | OS/2 2.1 | 20-40MB | (For operating system) | | | | | | | Minimum of | (For swapper file) | | | 10MB | | | | | (For multimedia | | | 5MB | support) | | | | | | | | OS/2 2.1 can be in a | | | | primary partition or | | | | logical drive. If you | | | | choose a minimum size | | | | for the partition, you | | | | might want to place | | | | the swap file on | | | | another partition. To | | | | do this, select Select | | | | features and install | | | | from the OS/2 Setup | | | | and Installation | | | | window. Then, select | | | | Software | | | | configuration. You | | | | can also install the | | | | WIN-OS/2 support in | | | | another partition. To | | | | do this, select | | | | WIN-OS/2 Support and | | | | its associated More | | | | push button from the | | | | OS/2 Setup and | | | | Installation window. | | | | | | | | If you want to install | | | | all features and you | | | | want the swap file on | | | | the same partition, | | | | consider making the | | | | OS/2 partition larger. | +----------+------------+------------------------+ > On page 83, add the following section before the section titled "Bypassing the Boot Manager Menu": Installing the Upgraded Version of MS-DOS 6.x If you are running a Dual Boot or Boot Manager configuration and you want to install the upgraded version of MS-DOS(**) 6.x, do the following: 1. Start your system with a current version of MS-DOS using a bootable MS-DOS diskette; do not use a Dual Boot or Boot Manager session. 2. Prepare an Uninstall Diskette so you can restore your previous version of DOS if needed. (Refer to your MS-DOS documentation for instructions.) 3. Edit the CONFIG.SYS and AUTOEXEC.BAT files. a. Type REM before each command line that starts a disk-caching, delete-protection, or antivirus program. Note: You need to disable the startup command for the MS-DOS SMARTDrive program. b. Disable any automatic message service, such as a network pop-up or a printing notification that is displayed on your screen. c. Save your changes to the CONFIG.SYS and AUTOEXEC.BAT files. d. Restart your system with the current installed version of MS-DOS, but not from a Dual Boot or Boot Manager session. 4. Insert the MS-DOS 6.x SETUP Diskette 1 into drive A. 5. At the DOS command prompt, type: A:SETUP 6. If your system is setup to use OS/2 Boot Manager, you will receive a message that states "This partition will not be available when using MS-DOS 6.x." Ignore this message and choose Continue Setup. If your system is setup to use OS/2 Dual Boot, you will receive a message prompting you to remove the non-MS-DOS operating system files from the drive. Ignore this message and choose Do Not Remove the Files. You will also receive a message stating "The operating system on the drive may be disabled." Ignore this message and choose Continue Setup. 7. Follow the instructions on your screen. If you need help during any of these procedures, press F1 for Help. 8. When you are prompted to do so, insert the diskette created in step 2 into drive A. 9. Restart your system when you have completed the Setup program. The system should start in MS-DOS 6.x. Warning: The MS-DOS 6.x installation program suggests that you run the MS-DEFRAG and MS(**) DOUBLE SPACE utility programs. These utility programs are not compatible with the OS/2 environment, and might cause data loss in OS/2 if executed. Other MS utility programs that perform direct diskette I/O, such as Interlink and UNDELETE, could compromise the OS/2 file system and are not supported. 10. To make the OS/2 system partition active again: o If your system is setup to use OS/2 Boot Manager, do the following: a. Type FDISK at the command prompt. b. When the FDISK screen appears, choose option 2; then press Enter. c. Choose the number that corresponds with the Boot Manager partition; then press Enter. d. When the confirmation screen appears, press Esc. e. Press Esc again to exit FDISK. f. Restart your system. o If your system is setup to use OS/2 Dual Boot, copy the COMMAND.COM file from the \DOS directory to the root directory. Note: SETUP places your previous DOS files in a directory named OLD_DOS.x. If you are sure you do not want to restore your previous version of DOS, you can delete the directory and its contents by typing DELOLDOS at the command prompt. CHAPTER 5. USING A RESPONSE FILE TO INSTALL ____________________________________________ > On page 87, replace the instructions after the first paragraph with the following: This procedure requires unpacking compressed files. To do this, copy the UNPACK2.EXE file from Diskette 2 to your hard drive. Any unpack instructions should be performed from this hard drive. 1. Make a copy of Diskette 1. You will modify only this copy. 2. Make extra room on the copy of Diskette 1 by deleting the following files, which will not be needed in a response file installation: a. Delete the MOUSE.SYS, SYSINST2.EXE, and BUNDLE files from the copy of Diskette 1. Note: Deleting the BUNDLE file is not necessary for CD-ROM installation. b. If you are installing OS/2 2.1 on a Micro Channel(*) computer, delete the IBM1*.ADD file from the copy of Diskette 1. c. If you are installing OS/2 2.1 on a non-Micro-Channel computer, delete the IBM2*.ADD and *0S.SYS files from the copy of Diskette 1. 3. Edit the CONFIG.SYS file on the copy of Diskette 1: a. Change the SET OS2_SHELL statement from "SET OS2_SHELL=SYSINST2.EXE" to the following: SET OS2_SHELL=RSPINST.EXE A:\OS2SE20.RSP b. Delete the following statement: DEVICE=MOUSE.SYS c. If you are installing OS/2 2.1 on a Micro Channel computer, delete the following statements in the CONFIG.SYS file on the copy of Diskette 1: BASEDEV=IBM1FLPY.ADD BASEDEV=IBM1S506.ADD d. If you are installing OS/2 2.1 on a non-Micro-Channel computer, delete the following statements in the CONFIG.SYS file on the copy of Diskette 1: BASEDEV=IBM2FLPY.ADD BASEDEV=IBM2ADSK.ADD BASEDEV=IBM2SCSI.ADD 4. Use the following statement to unpack the compressed file REQUIRED that is located on Diskette 11 and copy the SAMPLE.RSP file contained within it to the root directory of your hard drive: UNPACK2 A:\REQUIRED C:\ /N:SAMPLE.RSP a. Use an editor (such as the System Editor) to modify and save the file. The file contains comments that explain each of the installation options. b. Copy this modified response file to the copy you made of Diskette 1 and rename it OS2SE21.RSP. For example: COPY C:\SAMPLE.RSP A:\OS2SE21.RSP 5. Use the following statement to unpack the compressed file REQUIRED that is located on Diskette 7 and copy the RSPINST.EXE file contained within it to the root directory of your hard drive: UNPACK2 A:\REQUIRED C:\ /N:RSPINST.EXE 6. Copy the RSPINST.EXE file to the copy of Diskette 1. 7. If you have a Micro Channel computer and the Reference Diskette contains ABIOS.SYS and *.BIO files, you will also need to modify the Installation Diskette: a. Make a copy of the OS/2 2.1 Installation Diskette. b. Delete the *.BIO and ABIOS.SYS files from the copy of the Installation Diskette. c. Copy the *.BIO and ABIOS.SYS files from the Reference Diskette to the copy of the Installation Diskette. Note: This Installation Diskette copy is now system-specific. You will need to create a modified Installation Diskette for each type of system on which you are installing OS/2 2.1. d. Use this copy of the diskette during the installation process. 8. Begin the installation of the workstation by inserting the copy of the Installation Diskette and restarting the system. 9. When prompted for Diskette 1, insert the modified copy of Diskette 1 and press Enter. From this point, the installation program will prompt only for the insertion of diskettes. No other installation actions are necessary. 10. When prompted to insert Diskette 1 again, insert the original copy of Diskette 1 into drive A. Note: If you are installing from diskettes, you will be prompted to insert the Installation Diskette after the display driver diskettes; insert Diskette 1 instead. Response files can be used to install the same set of options on multiple workstations. You must ensure that the workstations are set up with the same set of options and hardware. > On page 88, add the following after the first paragraph under the section titled "Installing OS/2 2.1 from a Local Area Network Source": Requirements for remote installation of OS/2: o The RAM requirements vary from 6MB to 10MB or more, depending on the installation variables. -- Redirected remote installation requires more RAM than disk installation because the SWAPPER.DAT file is not active. -- If you are doing a redirected remote installation without CID, you only need about 6MB of RAM. -- When using CID, the RAM requirements usually range from 6MB to 8MB. -- If you are using a process on top of CID, like NVDM/2, 8MB to 10MB (or more) might be required. The main variable with CID is the size of the REXX procedure and which dynamic link libraries it pulls in. With remote installation, the LAN connection utility programs are the main variables. The version of OS/2 that you are installing is another variable. -- The reduced diskette version of OS/2 2.1 (20 diskettes) requires more RAM because of the new UNPACK2.EXE routine. o During remote installation, the SWAPPER.DAT file is not active because the disk partition containing the active swapper file cannot be formatted during installation. The SWAPPER.DAT file can be made active, but the disk partition has to be a local partition and preformatted. In order to activate the SWAPPER.DAT file, the CONFIG.SYS file has to be edited. To do this, replace the existing MEMMAN=NOSWAP statement with the following: MEMMAN=SWAP,PROTECT SWAPPATH=D:\ 2048 4096 o Personal Computers might require more RAM as the network drivers might have to store more data into the RAM buffers until the processor is able to handle the data. APPENDIX A. ADDING FEATURES AND CHANGING YOUR ______________________________________________ SYSTEM CONFIGURATION ____________________ > On page 107, add the following note before the section titled "Description of the System Configuration Choices": Note: Make sure that the same diskettes used for the installation of OS/2 2.1 are used for Selective Install. There are two levels of diskettes, compressed and uncompressed. These diskettes are identical except for the purpose of Selective Install. The compressed diskettes have salmon-colored labels, and the uncompressed diskettes have blue-colored labels. > On page 114, add the following note after the heading titled "Installing Display Drivers Using Display Install": Note: If you want to install display drivers using Display Install, you must have OS/2 DOS Support installed. APPENDIX B. DIAGNOSING SYSTEM PROBLEMS _______________________________________ > On page 117, replace the first list entry with the following: o Single inline memory modules conflicts You might encounter problems if the single inline memory modules of your computer system were produced by different manufacturers, are of different classes, or operate at different speeds. Refer to the TRAP0002 message for more information. > On page 118, add the following after the last list entry: o Disk Read Error Systems with a HYPERACE(**) 486 Upgrade might receive a "Disk Read Error" when trying to read Diskette 1 during installation. Several switches on the HYPERACE card might need to be disabled: 1. Switch 1 - disables the main cache. 2. Switch 2 - disables the HIMEM cache. 3. Switch 4 - disables the BIOS cache. After installation, reset the switches to enable the caches. For more information on the procedures, check the HYPERACE card documentation. > On page 119, replace the line "Messages beginning with "TRAP"" with the following: Messages beginning with "TRAP0002" > On page 121, add the following messages: +--------------------------------------------+ | | | An error occurred when System Installation | | tried to locate the KBD01.SYS file. | | | +--------------------------------------------+ Explanation: The installation program could not locate the KBD01.SYS file on a system with a Micropolis(**) SCSI hard drive. This file is not located in the default path or the path specified in the CONFIG.SYS file. Action: (1) Edit the CONFIG.SYS file and add the following statement: DEVICE=KBD01.SYS (2) Disable the "Read ahead cache" in the UTIL.EXE. +--------------------------------------------+ | | | An error occurred when System Installation | | tried to load the dynamic link library. | | | +--------------------------------------------+ Explanation: The installation program could not load the dynamic link library because there is not enough random access memory (RAM). Action: Add more system memory (RAM). +--------------------------------------------+ | | | A disk read error occurred. | | | +--------------------------------------------+ Explanation: The BIOS level of the Future Domain(**) adapter is not compatible. Action: Contact Future Domain for a BIOS upgrade if you own: o Future Domain TMC-850/860/875/885 with BIOS revision level 7.0. o Future Domain TMC-1660/1670/1680 with BIOS revision level 2.0. > On page 122, replace the COUNTRY.SYS message with the following: +--------------------------------------------+ | | | COUNTRY.SYS file cannot be found | | | +--------------------------------------------+ Explanation: The OS/2 operating system does not recognize the hard disk or diskette. (1) If you have a PS/2(*) P70, you need to request an engineering change. (2) A diskette drive or a hard disk drive controller might have an additional device (such as a tape backup) attached to it. (3) The diskette drive or hard disk drive controller might not reside at its own interrupt request (IRQ) level. (4) The hard disk partition on which you are installing OS/2 2.1 was compressed with a DOS data compression program. (5) If you have a Gateway(**) Nomad(**) laptop computer with Phoenix(**) BIOS 1.02, you will have to update the BIOS to the next level. (6) If your system is using an AMI(**) Fast Disk or a Fast Disk II SCSI adapter, they will be recognized as Adaptec adapters. (7) You have more than two (2) hard drives in the system. Action: (1) Contact your IBM customer engineer or computer dealer and request the engineering change announcement "ECA068." (2) Disconnect the device, if possible. (3) Refer to the operations manual that came with your computer for information about the IRQ setting. (Refer to OS/2 2.1 Using the Operating System for more information about setting IRQ levels.) (4) Use the data compression program to decompress the partition, and then retry the installation. (5) Update your Gateway Nomad Laptop computer with Phoenix BIOS 1.03 or later. (6) After installation, edit the CONFIG.SYS file as follows: o Delete any line with the following: BASEDEV=AHA1xxx.ADD where xxx can be any character. o Ensure that the statement BASEDEV=IBMINT13.I13 is included. (7) Check the partitions on any drives beyond the first two drives. If they are primary partitions, back up the data and re-partition them as logical drives. > On page 123, replace the TRAPxxx message with the following: +--------------------------------------------+ | | | TRAPxxx | | | +--------------------------------------------+ Explanation: In general, traps are symptoms of software-related problems. After you have pursued these symptoms from a software failure perspective, you should consider the potential of a hardware cause relating to caches and memory. (1) If your computer has an 80486 microprocessor, your computer might require faster RAM chips (60ns or 70ns). (2) There might be a problem with the external (level 2) CPU memory cache or main memory system on ISA or EISA systems. Action: (1) From the setup/diagnostics diskette or the BIOS Setup program built into the computer, try disabling all shadow RAM and external (level 2) CPU memory cache. (2) If problems persist during the installation of OS/2 after performing the above action, turn off the turbo switch (if one is available) on your system and retry the operation. Disable caching during installation or turn the turbo switch off. > On page 123, add the following messages: +--------------------------------------------+ | | | TRAP0002 | | | +--------------------------------------------+ Explanation: A TRAP0002 error can be a memory parity error on the system board or on an adapter card. (1) Your computer system might have single inline memory modules that were produced by different manufacturers or that operate at different speeds. Or, your computer system might have different classes of single inline memory modules. (For example, a 1x9 module cannot be used with a 1x3 module.) Action: (1) Remove any defective single inline memory module. It might also be necessary to replace one or more modules. (2) If your IBM computer is a 33 MHz and the microprocessor card part number is 84F9356, contact your local IBM representative and request an ECA053. (3) If the Memory Riser card part number is N33F4905 or 84F9356 on an IBM Model 8590 system, contact your local IBM representative and request an ECA084. +--------------------------------------------+ | | | SYS0005 | | | +--------------------------------------------+ Explanation: When trying to do a redirected remote installation of OS/2 2.1 using SYSINST2 for panel installation, the error message SYS0005 appears while attempting to copy UNPACK.EXE. Action: This Access Denied Error is caused by damage to the extended attribute data on the NetWare(**) Server. To correct this problem, delete the old disk images on the server and create new OS/2 disk images. > On page 124, add the following message: +--------------------------------------------+ | | | SYS1719 | | | +--------------------------------------------+ Explanation: The file IBM386FS\HPFS386.IFS does not contain a valid device driver or file system driver. Action: Edit your CONFIG.SYS file and delete the following line: IFS=x:\OS2\HPFS.IFS > On page 124, replace the SYS2025 message with the following: +--------------------------------------------+ | | | SYS2025 | | | +--------------------------------------------+ Explanation: A disk read error occurred. This might be a disk error or a damaged system boot record. Action: (1) If this error occurred while the system was loading, follow the procedure under "Recovering from Errors on the Hard Disk". (2) If this error occurred when the system was reading the installation diskettes, there might be an error on the diskette. If you already have an operating system installed on your computer, use the DISKCOPY command to make a copy of the installation diskettes. Retry the installation with the newly copied diskettes. (3) If your computer has BIOS supplied by AMI or Phoenix, you might need to upgrade the BIOS. Refer to Appendix G. (4) If your system has a local bus IDE controller card, disable the BIOS on the 32-bit local bus IDE controller card and use the generic INT13 driver instead of IBM1S506.ADD. (5) Make sure that there is not a hardware problem with your hard disk controller or your diskette drive. > On page 125, replace the SYS2026 message with the following: +--------------------------------------------+ | | | SYS2026 | | | +--------------------------------------------+ Explanation: The file OS2LDR cannot be found. This is a hidden system file and must reside in the root directory of the drive from which the operating system is started. Action: (1) Make sure a non-system diskette is not in the diskette drive. If necessary, remove the non-system diskette and restart the system. (2) If the OS2LDR file is missing from the hard disk, start up the system using the Installation Diskette. Insert Diskette 1 and press Enter. (3) Copy the OS2LDR file from the Installation Diskette to the OS/2 partition. > On page 127, add the following after the paragraph under the heading titled Diskette 1: If you are installing on a system with an Allways(**) IN2000 SCSI adapter, an IPE or FDISK error is displayed during the installation of Diskette 1. Upgrade your system to the current BIOS level of VCN:1-02. The Allways IN2000 SCSI adapter might require an EPROM upgrade to operate with OS/2 2.1. You might find that you have some problems when trying to install over DOS partitions. To correct these problems, you need to install the EPROMS and reformat the hard drive. If you are installing OS/2 2.1 on a MYLEX system, a TRAP0008 error occurs during the installation of Diskette 1. For more information on this error, contact MYLEX. If you are installing on a Compaq(**) 386/331 Deskpro system, a TRAP000D error occurs during the installation of Diskette 1. To correct this problem, do the following: 1. Make a copy of Diskette 1. You will modify the copy. 2. Use an editor to edit the CONFIG.SYS file that exists on the copy of Diskette 1. 3. Delete the following statements: BASEDEV=IBM2M57.ADD BASEDEV=IBM2SCSI.ADD 4. Use the copy of the diskette during the installation process instead of the original. > On page 127, add the following list entry after Diskette 3: o Diskette 6 If the system refuses Diskette 6 and makes a beeping sound, your system might be infected with the Joshi virus. The Joshi virus is a DOS virus that interferes with OS/2 and seems to cause random lockups. The Joshi virus: -- Operates by trapping disk reads and writes. If the virus is active in memory, programs that try to locate the virus on diskette will have problems detecting it. -- Is carried on the boot sector of an infected data diskette or system diskette. This virus originated in DOS but can survive in OS/2. When you start an infected system, the virus resides in memory and survives a Ctrl+Alt+Del startup. If the user does not type in the text "Happy Birthday Joshi", the system will stop. -- Is copied to the boot sector of every diskette. The virus will be transferred to any computer on which the user performed any diskette operation that included reading from, or writing to, the infected diskette. -- Spreads from infected diskettes to DOS and OS/2 systems when the systems are started from diskettes. -- Interferes with the startup from the hard disk of OS/2-based systems. The warning that OS/2 will give is that the IBM1FLPY.ADD file is bad or missing. Many antivirus packages are effective at detecting this virus. In DOS, The Norton Antivirus(**) Version 2.1 can both detect and clear the virus. The Joshi virus can also be cleared from DOS-based systems with the undocumented FDISK parameter MBR. However, the FDISK.EXE must be copied to and run from each partition. Type the following: FDISK /MBR This procedure causes the master boot record to be refreshed by the system, and the Joshi virus is overwritten. However, this procedure does not remove the virus from memory. The system needs to be restarted and rescanned for the virus. In OS/2, Central Point(**) Antivirus can detect the virus. McAfee(**) Clean and Scan can both detect and clear the virus. For more information on this antivirus program, contact McAfee Associates at (408) 988-3832. > On page 127, add the following to the end of the page: Installation on a Quantum II XL Hard Card If you have a Quantum(**) hard card, you must make a modification to the BASEDEV=IBM1S506.ADD line in the CONFIG.SYS file. To modify the BASEDEV statement, do the following: 1. Edit the CONFIG.SYS file on Diskette 1. 2. Change the BASEDEV statement to: BASEDEV=IBM1S506.ADD /A:1 /IRQ:11 3. Save the CONFIG.SYS file. 4. Install OS/2 2.1. (These are the default settings for the Quantum hard card.) Black Lines on a OS/2 Logo Screen During the installation on a Gateway 2000 with an 80486/66MHz processor, a local bus, and an ATI Graphics Ultra Pro, the system will get to the screen with the colorful OS/2 full-screen symbol, and then the installation will stop. The display screen shows horizontal bands of video separated by black bands that scroll horizontally across the screen. To correct this problem, do the following: 1. Start DOS. 2. Change the OS/2 directory to MACH32. 3. Type: INSTALL 4. At the Main Selection screen select Set Power up Configuration. 5. Select Monitor Type, and press Enter. 6. Select 1572 Monitor with 72Hz Refresh Rate, and press Enter. 7. Select IBM Default as the new display. Note: After OS/2 is successfully installed, repeat the steps to reselect the 1572 Monitor type. White Screen Appears during Installation If the display screen is white during the installation of OS/2 2.1 and there is no system activity, set the video adapter to operate on an 8-bit mode and move the adapter to an 8-bit slot. Do the following: 1. Turn off the system and disable the autosensing capability of the video adapter. 2. To modify the settings, refer to the documentation that came with your video adapter. 3. Place the adapter in an 8-bit slot until you have successfully installed OS/2 2.1. 4. The adapter can be returned to the 16-bit slot and set back to the 16-bit mode. > On page 128, add the following to the list entries: o System is unable to access the CD-ROM drive o Redirection of XGA$DMQS Directory is ignored o An error appears when using Dual Boot o White screen or blank screen after installation o OS/2 2.0 desktop does not migrate o Slow SCSI support o System will not start DOS > On page 129, add the following after the section titled "Adding Support for a Mouse": System Unable to Access CD-ROM Drive If you clicked on the CD-ROM check box on the System Configuration screen during the installation of OS/2, the installation program put the entry None in the CD-ROM text box and the CD-ROM files were not copied. Because some drives are not directly supported by the device drivers shipped with the OS/2 product, you must now select OTHER from the selection list to enable CD-ROM support. For Sony, Mitsumi, or Hitachi(**) users, if you cannot access your CD-ROM drive, restart your system and do the following: 1. Copy the following files from Diskette 1 to the hard disk: COPY A:\OS2CDROM.DMD C:\OS2 COPY A:\CDFS.IFS C:\OS2 2. Edit your CONFIG.SYS file on the hard disk and add the following statements: DEVICE=C:\OS2\OS2CDROM.DMD /Q IFS=C:\OS2\CDFS.IFS /Q 3. Perform a shutdown and restart the system. For Sound Blaster users with the device driver SBPCD2.SYS, if you cannot access your CD-ROM drive, restart your system and do the following: 1. Copy the following file from Diskette 1 to the hard disk: COPY A:\CDFS.IFS C:\OS2 2. Edit the CONFIG.SYS file on the hard disk and add the following statement: IFS=C:\OS2\CDFS.IFS /Q 3. Restart your system to OS/2. 4. Start the Selective Install program in the System Setup folder. a. Click on the CD-ROM Device Support check box on the System Configuration screen. b. Click on OK to display the CD-ROM selection list. Scroll to the bottom of the list, select the choice OTHER and click on OK. 5. Continue the Selective Install process until completed. 6. Edit the CONFIG.SYS file and delete the following line: REM DEVICE=C:\OS2\OS2CDROM.DMD /Q 7. Perform a shutdown and restart the system. > On page 130, add the following before the section titled "Problems with a Mouse Not Working": Redirection of XGA$DMQS Directory Ignored during Installation The installation program copied the XGA$DMQS files to the same partition as the operating system. To correct this problem, do the following: 1. XCOPY the XGA$DMQS directory from the drive containing OS/2 2.1 to the redirected drive. a. Start an OS/2 session. b. Type XCOPY C:\XGA$DMQS D:\XGA$DMQS /S (where C is the drive containing OS/2 2.1 and D is the redirected target drive) c. Press Enter. 2. Edit the C:\CONFIG.SYS file. 3. Add the following line to the file: SET DMQSPATH=D:\XGA$DMQS 4. Save the changes and exit the editor. 5. Perform a shutdown and restart the system. > On page 131, add the following sections before the section titled "LOGO Screen Problems": Mouse Not Working after Selective Install If you did a selective installation of a new mouse and the mouse is not working, you will need to edit your CONFIG.SYS file. To edit the CONFIG.SYS file, do the following: 1. Open OS/2 Window. 2. Type: e config.sys and press Enter. 3. Delete the mouse device driver statements. For example: DEVICE=C:\OS2\MOUSE.SYS Note: If your mouse device driver is not for a Microsoft or PS/2 mouse, you might have two DEVICE= statements to delete. 4. Save the file. o Pull-down the File menu by pressing F10 and then Enter. o Select Save As. o Type in the CONFIG.SYS file name and press Enter. 5. Exit the System Editor by pressing Alt+F4. 6. Shut down and restart the system. Error When Using Dual Boot on a PS/1 System On PS/1(*) systems preinstalled with DOS 5.0, using Dual Boot from OS/2 to DOS results in an error. To correct this problem, press and hold Ctrl+Alt, and press Del to restart the system. > On page 132, change the heading to "White Screen or Blank Screen Problems" and add the following information after the first paragraph: On restarting the system after the complete installation of OS/2, the desktop appears to be blank. If the display screen is blank, performing CHKDSK on the drive connected to the ProComm(**) Micro Channel SCSI adapter might result in the system not working. To correct this problem, contact ProComm to receive the device driver needed for the SCSI card. > On page 132, add the following section before the section titled "Making the Boot Manager Startable": The OS/2 2.0 Desktop Does Not Migrate After OS/2 2.1 Installation After you install OS/2 2.1, you might have some problems migrating the OS/2 2.0 desktop. o If you have a desktop problem, do the following: 1. Insert the Installation Diskette and turn on the computer. 2. Insert Diskette 1 3. Press Esc at the Welcome screen to get to the command prompt. 4. Delete the DESKTOP directory. 5. Restart the system; the desktop should be re-created. 6. If the problem continues, you must run the MAKEINI program. o If you have moved program groups off the desktop and into a folder, you should move them back on the desktop before installing OS/2 2.1. Otherwise, duplicate icons could appear on the screen. If you try to delete these icons, the original icons will also be deleted. o If you want to recover a backed up OS/2 2.0 desktop, you can use the following procedure: 1. Insert the Installation Diskette, and turn on the computer. 2. Press Esc to get to the command prompt. 3. Delete or rename the INI files on the hard disk. 4. Copy the backup INI files to the OS/2 subdirectory. 5. Run the MAKEINI OS2.INI INI.RC program. 6. Run the MAKEINI OS2SYS.INI INISYS.RC program. 7. Delete the DESKTOP directory. 8. Restart the system. Notes: 1. If you try to recover the backed up OS/2 2.0 desktop, the customization for the OS/2 2.1 desktop will be lost. 2. The name of your DESKTOP directory might be slightly different. To find the actual name of your DESKTOP directory currently in use, display the Settings notebook for the desktop and select the File page. The current desktop name is shown under Physical name. > On page 133, add the following section before the section titled "Existing Application Not Migrated": Slow SCSI Support or Missing Icons After installation, slow SCSI support occurs. In addition, evidence of data damage such as missing icons might also occur. Check the documentation for the hard drive and the controller card to ensure that their settings are both set for the ASYNCH mode or the SYNCH mode. > On page 133, add the following sections to the end of the page: System Will Not Start DOS from the Boot Manager Menu On a system with a VESA SUPER I/O controller and two disk drives, the system will not start DOS from the Boot Manager menu. It will display a non-system disk or disk error message. For more information on this message, check the VESA controller documentation or contact the manufacturer. Running CHKDSK To run CHKDSK /F using diskettes: 1. Insert the Installation Diskette into drive A. 2. Turn on the computer. If the computer is already on, press and hold Ctrl+Alt, and press Del to restart the system. 3. When you are prompted to do so, remove the Installation Diskette and insert Diskette 1. 4. Press Enter. 5. When the Welcome screen is displayed, press Esc to display the command prompt. 6. Remove Diskette 1 and insert Diskette 2. Type: CHKDSK C: /F and press Enter. Note: If your operating system resides on a drive other than C, use the appropriate drive letter instead. > On page 137, add the following to the end of item 7: To run CHKDSK from a CD-ROM: 1. Insert the Installation Diskette into drive A. 2. Shut down and restart the system. 3. When prompted to do so, remove the Installation Diskette and insert Diskette 1; then press Enter. 4. When prompted to do so, insert the CD in the CD-ROM drive, and then press Enter. 5. When the Welcome screen is displayed, press Esc to display the command prompt. 6. To change directories, type: CD\ and press Enter. 7. Type: CD OS2SE2 and press Enter. 8. Type: CD DISK_2 and press Enter. 9. Type: CHKDSK x: /F (where x is the drive letter of your OS/2 system partition) and press Enter. APPENDIX F. MIGRATING FROM OS/2 EXTENDED EDITION _________________________________________________ TO OS/2 2.1 ___________ > On page 166, add the following note to the end of the page: Note: If you are installing OS/2 2.1 on a system with a LAN SERVER 3.0 and a HPFS386, you will get a SYS1719 error message. Refer to the "SYS1719" message for more information. APPENDIX G. UPGRADING THE BIOS OF YOUR COMPUTER ________________________________________________ > On page 167, replace the sentence about Phoenix BIOS with the following: For questions about products that use Phoenix BIOS, call the computer manufacturer directly. If there are additional questions, call Phoenix at (714) 440-8080. APPENDIX H. NOTICES ____________________ > On page 171, add the following new appendix: Note: "Notices" will then become Appendix I. Appendix H. Creating an OS/2 Startup Diskette The following procedure explains how to create a startup diskette for OS/2 2.1. 1. Insert the Installation Diskette into drive A. 2. Copy the SYSINSTX.COM file to your OS/2 directory. 3. Remove the Installation Diskette from drive A. 4. Insert Diskette 1 into drive A. 5. Copy the KEYBOARD.DCP and SYSINST1.EXE files to a subdirectory on your hard disk. 6. Use the ATTRIB command to display the OS2KRNL, OS2LDR, and OS2LDR.MSG files. 7. Remove Diskette 1 from drive A. 8. Insert a blank, formatted diskette into drive A and type: SYSINSTX A: 9. Copy the OS2KRNL, OS2LDR, and OS2LDR.MSG files to the startup diskette, and then use the ATTRIB command to hide the files. 10. Copy the KEYBOARD.DCP and SYSINST1.EXE files from the subdirectory to the startup diskette. 11. Copy the following libraries from the \OS2\DLL directory to the startup diskette: ANSICALL.DLL DOSCALL1.DLL NLS.DLL NPXEMLTR.DLL BKSCALLS.DLL KBDCALLS.DLL OS2CHAR.DLL BMSCALLS.DLL MOUCALLS.DLL QUECALLS.DLL BVHINIT.DLL MSG.DLL SESMGR.DLL BVSCALLS.DLL NAMPIPES.DLL VIOCALLS.DLL 12. Copy the HARDERR.EXE and COUNTRY.SYS files from the \OS2\SYSTEM directory to the startup diskette. 13. Copy the SYSLEVEL.OS2 file from the \OS2\INSTALL directory to the startup diskette. 14. Copy the CMD.EXE, DOS.SYS, IBMINT13.I13, and OS2DASD.DMD to the startup diskette from the \OS2 directory. If you are planning to use HPFS, you need to copy the HPFS.IFS file to the startup diskette. 15. If you have an AT(*) system, copy the CLOCK01.SYS, KBD01.SYS, PRINT01.SYS, SCREEN01.SYS, and IBM1FLPY.ADD files to the startup diskette. 16. If you have a Micro Channel PS/2 system, copy the CLOCK02.SYS, KBD02.SYS, PRINT02.SYS, SCREEN02.SYS, and IBM2FLPY.ADD files to the startup diskette. The following command is used to copy the ABIOS.SYS file on the startup diskette for a PS/2 system: ECHO . > A:ABIOS.SYS 17. If you have a SCSI hard drive, copy the IBM2SCSI.ADD file (or the .ADD file from the manufacturer). If you have a hard drive other than a SCSI hard drive, copy the IBM1S506.ADD file to the startup diskette. 18. Using an editor, create the following CONFIG.SYS file on the startup diskette (in this case, for HPFS): IFS=HPFS.IFS /CACHE:64 BUFFERS=32 IOPL=YES MEMMAN=NOSWAP PROTSHELL=SYSINST1.EXE SET OS2_SHELL=CMD.EXE DISKCACHE=64,LW PROTECTONLY=YES LIBPATH=.;\; PAUSEONERROR=NO CODEPAGE=850 DEVINFO=KBD,US,KEYBOARD.DCP DEVICE=\DOS.SYS SET PATH=.;\ SET DPATH=\; SET KEYS=ON BASEDEV=PRINT0x.SYS (where x is 1 for AT; 2 for Micro Channel BASEDEV=IBMxFPLY.ADD (where x is 1 for AT; 2 for Micro Channel BASEDEV=IBMINT13.I13 BASEDEV=OS2DASD.DMD a. If you have a SCSI drive on a Micro Channel computer, add the following statement to this file: BASEDEV=IBM2SCSI.ADD b. If you have a hard drive other than a SCSI drive on a non-Micro Channel computer, add the following statement to this file: BASEDEV=IBM1S506.ADD c. If you have any space left on your diskette, copy the CHKDSK.COM file from the \OS2 directory to the startup diskette. PART 2: CHANGES TO OS/2 2.1 USING THE OPERATING SYSTEM Part 2 contains information that is new or different from the information in the OS/2 2.1 Using the Operating System book. The chapter numbers and titles in this booklet are the same as those used in the Using the Operating System book; only those chapters of the Using book that are changed are included here. ABOUT THIS BOOK _______________ > On page xxvi, replace the last three entries of the list in the section titled "How This Book is Organized" with the following list entries: o Appendix A describes the keys and mouse actions used in tasks. o Appendix B contains some of the most common error messages. o Appendix C describes how to back up and restore the desktop. o Appendix D describes the OS/2 file systems. o Appendix E describes the file locations. o Appendix F describes how to remove programs. o Appendix G contains forms for recording information about your computer. o Appendix H contains warranty and service information for the mini-applications and productivity aids. o Appendix I describes the Memory Dump process. o Appendix J contains the trademarks and service marks. o Glossary of the terms used in this book. o Index. NEW FEATURES IN OS/2 2.1 ________________________ > On page xxx, replace the list entry "The Ultimotion(*) software motion video formats" with the following: o Ultimotion and Video software motion video formats CHAPTER 1. GETTING STARTED WITH OS/2 2.1 _________________________________________ > On page 23, add the following instructions at the end of the section titled "Renaming an Object": You can also change the object name by performing the following steps: 1. Select the object whose name you want to change. 2. Press Shift+F9. 3. Type the new name in the Title field. 4. Press the Enter key on the numeric key pad. Note: Press Ctrl+Shift+Enter for any computer that does not have a numeric keypad. > On page 40, replace the first set of lockup instructions in the section titled "Locking Up Your System" with the following: To lock your system manually: 1. Point to an empty area on the desktop. 2. Click mouse button 2. 3. Select Lockup now. If this is the first time you have locked up the keyboard, a window appears where you can set up a password. (You will use this password later to unlock the keyboard so that you can use the computer.) 4. Type your password. 5. Carefully type your password again for verification. Note: If you forget your password, you must turn the computer off and then on again to unlock the keyboard. Any information that was not saved before the keyboard was locked will be lost. First Edition (January 1994) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time. It is possible that this publication may contain reference to, or information about, IBM products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that IBM intends to announce such IBM products, programming, or services in your country. Requests for technical information about IBM products should be made to your IBM authorized reseller or IBM marketing representative. (C) Copyright International Business Machines Corporation 1994. All rights reserved. Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp. --------------- (*) Trademark of the IBM Corporation. (**) Trademark of Adaptec, Inc. (*) Trademarks of the IBM Corporation. (**) Docking Station is a trademark of NEC Home Electronics, Inc. (**) ATI and Ultra are trademarks of ATI Technologies, Inc. Gateway 2000 is a trademark of Gateway 2000, Inc. Sony is a trademark of Sony Corporation. Panasonic is a trademark of Matsushita Electric Industrial Co., Ltd. Mitsumi is a trademark of Mitsumi Denki Kabushki Kaisha. (**) Media Vision and ProAudio Spectrum are trademarks of Media Vision, Inc. Sound Blaster is a trademark of Creative Labs, Inc. (*) Trademark of the IBM Corporation. (**) Microsoft and Windows are trademarks of the Microsoft Corporation. (**) VESA is a trademark of Video Electronics Standards Association. (**) MS-DOS is a trademark of the Microsoft Corporation. (**) MS is a trademark of the Microsoft Corporation. (*) Trademark of the IBM Corporation. (**) HYPERACE is a trademark of Hypertec Pty. Limited. (**) Micropolis is a trademark of Micropolis Corporation. Future Domain is a trademark of Future Domain Corporation. (*) Trademark of the IBM Corporation. (**) Gateway is a trademark of Gateway Systems Corporation. Nomad is a trademark of Gateway 2000, Inc. Phoenix is a trademark of Phoenix Technologies, Ltd. AMI is a trademark of American Megatrends, Inc. (**) NetWare is a trademark of Novell, Inc. (**) Allways is a trademark of Funk Software, Inc. Compaq is a trademark of Compaq Computer Corporation. (**) The Norton Antivirus is a trademark of Symantec Corporation. (**) Central Point is a trademark of Central Point Software, Inc. McAfee is a trademark of McAfee Associates. Quantum is a trademark of Quantum Corporation. (**) Hitachi is a trademark of Hitachi Ltd. (*) Trademark of the IBM Corporation. (**) ProComm is a trademark of Datastorm Technologies, Inc. (*) Trademark of the IBM Corporation. (*) Trademark of the IBM Corporation. CHAPTER 4. SYSTEM SETUP ________________________ > On page 68, add the following note to the end of the page: Note: If the keyboard speed is set in WIN-OS/2, when that WIN-OS/2 session is started, the keyboard speed for the entire system is reset and remains reset even after that WIN-OS/2 session is closed. > Replace the Power section at the end of this chapter with the information that follows. POWER The Power object manages and tracks power consumption in battery-powered computers that support the Advanced Power Management (APM) standard. The APM standard defines the way the hardware and software work together to reduce power consumption and help extend battery life. If your computer supports the APM standard, the Power object might be automatically installed during the OS/2 2.1 installation process. If it was not installed, you can install it by using Selective Install and selecting Advanced Power Management. For information about Selective Install, see "Selective Install". Note: This power management feature is not available if your computer does not have APM BIOS or a device driver that emulates APM BIOS. OS/2 2.1 APM support relies on the power status information returned from the BIOS on your computer. You might notice incorrect battery life or status within the Power icon on your computer. If this occurs, rely on the LEDs on your computer for accurate power status information. Turning the APM setting to Off also turns off the BIOS power management. If you want to turn off APM, but not the BIOS power management, place REM before the APM device driver statement in your CONFIG.SYS file, and then restart your system to invoke the change. For example: REM DEVICE=C:\OS2\APM.SYS Power Object To open the Power object: 1. Open OS/2 System. 2. Open System Setup. 3. Open Power. To display the Power pop-up menu: 1. Point to the Power object. 2. Click mouse button 1 or 2. Power Settings To set power management support: 1. Display the Power object pop-up menu. 2. Select the arrow to the right of Open. 3. Select Settings. The Power - Settings notebook appears. 4. Select Power. 5. Set Power management to On or Off. If set to On, power consumption will be reduced and power status will be tracked. If set to Off, the suspend mode, power status, and battery status features are disabled. 6. Set Confirm on power state changes if you want to confirm requests to go to suspend mode. (See "Suspend Mode.") To set the default status view of the status window: 1. Display the Power object pop-up menu. 2. Select the arrow to the right of Open. 3. Select Settings. The Power - Settings notebook appears. 4. Select View. 5. Select Full status or Battery only for Default status view. 6. Set Refresh (of the status window) to On or Off. 7. If you set Refresh to On, select the number of minutes (from 1 to 30) for Refresh rate. The system will automatically update the status window at the intervals you specified. You can also update the status window by selecting Refresh Now from the Power object pop-up menu. Power Status To display the power status: 1. Display the Power object pop-up menu. 2. Select the arrow to the right of Open. 3. Select Full status or Battery status. A full-status Power window or a power-gauge Power window is displayed, depending on your selection. Note: You cannot change the size of the Power window. A full-status Power window displays the following information: o Battery life. This information is displayed as a power gauge that shows the power level of the battery compared to the capacity of the battery. When the power gauge indicator is completely shaded, the battery is at full power. The shaded area of the gauge moves up or down as the battery power level increases or decreases. When the power gauge indicator is dimmed, there is no battery in the computer or the computer cannot provide battery information. o Power source for the computer. If the system cannot determine the power source, no power source information is displayed. o Battery state, which is the charge state of the battery. Battery state information is displayed as follows: High Battery charge is OK; continue using your computer. Low Recharge the battery or switch to another power source such as another battery or AC power. Critical Battery charge is depleted. Recharge the battery or switch to another power source immediately to avoid a system failure or data loss. Charging System is restoring the battery charge. Unknown System cannot determine the battery state or there is no battery in your computer. Suspend Mode To set the suspend mode: 1. Display the Power object pop-up menu. 2. Select Suspend. When suspend mode is activated, battery power is conserved by dimming the display and turning off devices that are not in use. If Confirm on power status changes is set in the Power - Settings notebook, a message that asks you if you want to continue is displayed before switching to suspend mode. Note: Different computers have different procedures for exiting suspend mode and resuming operation. Refer to the documentation that came with your computer for information about its suspend mode features. After you exit suspend mode, you will notice a startup delay before you can resume operation of your system. This delay might be a few seconds, depending on your system. PCMCIA OS/2 2.1 provides software support for Personal Computer Memory Card International Association (PCMCIA) hardware. PCMCIA(**) is the standard for PC card adapters associated with portable computers. A PC card is a small form-factor adapter about the size and shape of a credit card. You can use PC cards with laptops, notebooks, tablets, and other portable computer systems that are equipped with a PCMCIA slot. To install PCMCIA, use Selective Install and select PCMCIA. For information about Selective Install, see "Selective Install". CHAPTER 5. STARTUP ___________________ > On page 93, replace all text after the first paragraph with the following: If you add hard disk drives or partitions after the installation of the OS/2 operating system, you should edit the CONFIG.SYS file and update the AC:x parameter to reflect the new additions. AC: starts the auto-check feature on the specified drives when the system shuts down improperly. The value x represents the letters of the disks or partitions on the system that you want to check. For example, if you want to check disks C and D and your existing DISKCACHE statement is: DISKCACHE=64,LW Add the AC: parameter to the statement as follows: DISKCACHE=64,LW,AC:CD CHAPTER 6. DRIVES __________________ > On page 95, add the following note before the section titled "About Hard Disks and Diskettes": Note: Drive objects cannot be copied. > On page 97, add the following note to the Tree view paragraph: Note: When an additional folder is opened from a folder that is in tree view, if the default for the additional folder is also tree view, it is overridden and displayed in an icon view. There is no need to open it again in tree view because it is already shown in the parent folder's tree view. --------------- (**) PCMCIA is a trademark of Personal Computer Memory Card International Association. > On page 101, replace the instructions in the section titled "Moving Objects" with the following: To move an object from a drive to another location: 1. Open the drive containing the object you want to move. 2. Point to the object you want to move. 3. Press and hold mouse button 2. 4. Drag the object to a folder, the desktop, or another drive object. 5. Release mouse button 2. > On page 102, replace the moving instructions with the following: To move an object from another location to a drive: 1. Point to the object you want to move. 2. Press and hold mouse button 2. 3. Drag the mouse to the drive object. 4. Release mouse button 2. > On page 109, replace instruction #16 with the following: 16. Type the following information into the data file: DEVICE=FSFILTER.SYS DEVICE=C:\OS2\MDOS\HIMEM.SYS DEVICE=C:\OS2\MDOS\EMM386.SYS DOS=HIGH,UMB DEVICEHIGH=C:\OS2\MDOS\ANSI.SYS FILES=20 BUFFERS=20 CHAPTER 8. PRODUCTIVITY ________________________ > On page 117, add the following note to the section titled "Picture Viewer": Note: Picture Viewer does not support multiple-page metafiles. CHAPTER 10. INFORMATION ________________________ > On page 133, replace line 3 of the instructions in the section titled "Printing the README" with the following: 3. Drag the README object to a printer object. CHAPTER 12. DRIVE A ____________________ > On page 139, add the following note before the section titled "Display the Objects on a Diskette": Note: The Drive A object cannot be copied. > On page 141, replace all the instructions following the note in the section titled "Copying Objects to or from a Diskette" with the following: To copy an object from a diskette in Drive A to another location: 1. Place a diskette into drive A. 2. Open Drive A. 3. Point to the object you want to copy. 4. Press and hold Ctrl. 5. Press and hold mouse button 2. 6. Drag the object to a folder, the desktop, or another drive object. 7. Release mouse button 2. 8. Release Ctrl. To copy an object from another location to a diskette in Drive A: 1. Place the diskette you want to copy the object to into drive A. 2. Point to the object you want to copy. 3. Press and hold Ctrl. 4. Press and hold mouse button 2. 5. Drag the mouse to the Drive A object. 6. Release mouse button 2. 7. Release Ctrl. > On page 142, replace all the instructions following the note in the section titled "Moving Objects to or from a Diskette" with the following: To move an object from the diskette in Drive A to another location: 1. Place a diskette into drive A. 2. Open Drive A. 3. Point to the object you want to move. 4. Press and hold Shift. 5. Press and hold mouse button 2. 6. Drag the object to a folder, the desktop, or another drive object. 7. Release mouse button 2. 8. Release Shift. Note: When moving an object from a diskette, the Shift key must be used with mouse button 2. To move an object from another location to the diskette in Drive A: 1. Place the diskette you want to move the object to into drive A. 2. Point to the object you want to move. 3. Press and hold Shift. 4. Press and hold mouse button 2. 5. Drag the object to the Drive A object. 6. Release mouse button 2. 7. Release Shift. Note: When moving an object to a diskette, the Shift key must be used with mouse button 2. CHAPTER 16. PRINTERS AND PLOTTERS __________________________________ > On page 166, add the following instruction between lines 7 and 8: 7a. Select Install new printer driver. CHAPTER 17. PREPARING YOUR PROGRAMS ____________________________________ > On page 185, add the following note before the section titled "Viewing Program Object Settings": Note: The PgUp and PgDn keys on the numeric keypad should not be used to move between pages. CHAPTER 18. USING WINDOWS PROGRAMS ___________________________________ > On page 196, replace the last sentence in the section titled "Character Map" with the following: Character Map works with Windows and OS/2 programs. > On page 199, replace all the text after the first paragraph in the section titled "Locating Window Programs" with the following: When you run the Migrate Applications program for existing Windows programs, the WIN-OS/2 Groups folder is created and placed on the desktop. The WIN-OS/2 Groups folder contains folders of Windows application programs that reside in the default groups, WIN-OS/2 Accessories and WIN-OS/2 Main. A group is a set of Windows programs that are related. The Windows Programs folder contains Windows programs that have settings preselected to optimize the performance of your program. Windows programs that do not belong to any group are migrated to the Windows Programs folder. The Additional Windows Programs folder contains Windows programs that have default settings for your programs. (If these programs do not run correctly, you can specify other settings.) For example, if you have CorelDraw(**) for Windows installed, when you run the Migrate Applications program, a folder for all the CorelDraw programs is created and placed in the Additional Window Programs folder. Now you have access to all the CorelDraw programs in one folder. For more information about migrating programs, see "Migrate Applications". > On page 201, replace the paragraph at the top of the page with the following: When you change the value of a setting before you start a session, the changes affect all programs running in that session. When you change the value of a setting while the session is running, the changes will not have any effect until you restart the session. If you want the changes to remain whenever you start a specific session or program, you must save the changes. > On page 201, add the following note before the section titled "Running Window Programs in WIN-OS/2 Sessions": Note: The changes will not take effect until you restart the session. > On page 202, replace the last sentence with the following: To run more than one Windows program, repeat the above steps as needed. > On page 205, replace the last paragraph before the section titled "Using the Clipboard and Dynamic Data Exchange Features" with the following: To switch between active WIN-OS/2 sessions, press Alt+Tab. CHAPTER 23. AUDIO SUPPORT FOR APPLICATIONS ___________________________________________ > On page 259, move the sentence that reads "If there are cells that have audio, each of these cells is shown, one by one, as selected and unshaded." to the end of the page. > On page 260, move the first paragraph beginning with "If the cell you select..." to after the delete instructions. Move the paragraph beginning with "If the work sheet is not synchronized..." to after the second set of instructions. PART 5: EXTRA HELP ___________________ > On page 263, replace the entry list with the following: o What to do when you have a problem o Tuning the performance of your system o Software support, including information about the OS/2 clipboard and Dynamic Data Exchange (DDE) o Video support, including information about Super VGA, XGA(*) systems, and laptop LCD displays o Printing support, including information about installing and configuring printer drivers o Hardware support, including information about high-resolution displays, CD-ROM drives, Advanced Power Management (APM), and mobile computing CHAPTER 24. SOLVING PROBLEMS _____________________________ > On page 267, replace the sentence in the first Action column that begins "Refer to 'Adding online documentation...'" with the following: Refer to "documentation, adding after installation" in the Master Help Index. > On page 273, replace the first paragraph in the Action column with the following: Download the program and try to run it without the network. If the program runs, the problem is probably related to the network. Ask your network administrator for assistance. > On page 282, replace the DOS setting "MOUSE_EXCLUSIVE_ACCESS DOS setting" in the Action column with the following: MOUSE_EXCLUSIVE_ACCESS > On page 285, replace the example beginning with "MODE COM3 ..." in the Action column with the following: MODE COM3 IDSR=OFF ODSR=OFF OCTS=OFF > On page 285, replace the paragraph beginning with "Fax programs must..." in the Action column with the following: DOS fax programs must operate at less than 9600 bps. Use an OS/2 fax program for high-speed faxing. CHAPTER 26. SOFTWARE SUPPORT _____________________________ > On page 301, delete the first sentence under Enhanced Editor. > On page 301, add the following section after Enhanced Editor: ES 1.0 Database Manager o To properly install the ES 1.0 Database Manager, the file ESSTART.BAK must be copied from the OS/2 2.1 Installation Diskette to the ES 1.0 installation diskette and renamed ESSTART.CMD. > On page 309, replace the statement beginning with "123MEMSIZE=2048 ..." with the following: SET 123MEMSIZE=2048 CHAPTER 27. VIDEO SUPPORT __________________________ > On page 334, replace the statement "UNPACK A:G.FON" with the following: UNPACK A:*G.FON CHAPTER 28. PRINTER SUPPORT ____________________________ > On page 353, add the following Lexmark(**) bulletin board phone number to the end of the first sentence in the section titled "IBM 4019 and IBM 4029 Printers": (1-606-232-5238) CHAPTER 29. HARDWARE SUPPORT _____________________________ > On page 363, replace the last entry under the Model column with the following: CR-501, LK-MC501S, MC501B > On page 366, replace the first paragraph in the Comments column with the following: IBM SCSI and Future Domain 16-bit SCSI adapters might work, but are not supported by IBM. > On page 373, each BASEDEV example should contain all of its parameters on one line. > On page 378, replace the example beginning with "DEVICE=X ..." with the following: DEVICE=X:\OS2\COM.SYS (n,a,i,s) > On page 383, add the following section: Advanced Power Management Support for Laptop Computers Laptop computers with the following are compatible with OS/2 2.11 Advanced Power Management: o 16-bit protect-mode APM in BIOS o 32-bit protect-mode APM in BIOS Laptop computers that have no APM support in BIOS or have only real-mode APM are not supported by OS/2 2.11 Advanced Power Management. The DOS utility program APMHERE, which is available on the IBM BBS, can quickly determine whether your machine has Advanced Power Management support in conformance to the APM 1.0 Specification (dated 1/91). Systems with BIOS dates prior to January 1991 will not have the protect-mode APM support in their BIOS. Laptop Computers with APM Support The table that follows lists the laptop computers that have Advanced Power Management support. (This list represents only systems tested as of January 27, 1994.) --------------- (**) CorelDraw is a trademark of Corel Systems Corporation. (*) Trademark of the IBM Corporation. (**) Trademark of Lexmark International, Inc. +------------------+--------------+--------------+ | Manufacturer | Model | Comments | +------------------+--------------+--------------+ | Acer America | AcerNote 730 | BIOS | | Corp. | | information | | | | displayed on | | | | start up: | | | | | | | | PhoenixBIOS|TM) A486 | | | Version 1.0| R1.0 +------------------+--------------+--------------+ | Acer America | AcerNote 750 | | | Corp. | | | +------------------+--------------+--------------+ | AST Research, | PowerExec | | | Inc. | 4/25SL | | +------------------+--------------+--------------+ | AST Research, | PowerExec | Perform the | | Inc. | 4/25SL Color | following | | | Plus | steps: | | | 486SL/25 | | | | Active | 1. Press FN | | | Matrix Color | F1 keys | | | | to get | | | | BIO | | | | access | | | | 2. Select | | | | Power | | | | Managemen| | | | 3. Click on | | | | Power | | | | Managemen| | | | Section | | | | 4. Follow | | | | the | | | | Character|ze | | | the | | | | Battery | | | | instructi|ns +------------------+--------------+--------------+ | Compaq Computer | 4/25 | | | Corp. | | | +------------------+--------------+--------------+ | Compaq Computer | CONTURA 4/25 | | | Corp. | Monochrome, | | | | VGA | | +------------------+--------------+--------------+ | Compaq Computer | CONTURA | | | Corp. | 4/25C | | | | 486SL/25 | | | | Active | | | | Matrix | | +------------------+--------------+--------------+ | Compaq Computer | CONTURA | See Note 1. | | Corp. | 4/25cx | | +------------------+--------------+--------------+ | Compudyne | 4SL/25 | BIOS | | | SubNOTEBOOK | information | | | | displayed on | | | | start up: | | | | | | | | PhoenixBIOS|TM) LAP486SL | | | Version 1.0| | | | PhoenixMISE|(TM) 486L v2.0 | | | 80486SL BIO| | | | Version 1.1| 5/28/93 +------------------+--------------+--------------+ | Gateway 2000, | ColorBook | | | Inc. | 486SX/25 | | | | 486SX/25 | | | | Dual Scan | | | | Color | | +------------------+--------------+--------------+ | Gateway 2000, | ColorBook | See Note 1. | | Inc. | 486DX/33 | Requires | | | 486DX/33 | corrected | | | Dual Scan | BIOS from | | | Color | System Soft, | | | | Inc.; see | | | | Note 2. | +------------------+--------------+--------------+ | Gateway 2000, | HandBook | See Note 1. | | Inc. | 486DX2/40 | Requires | | | 486DX2/40 | corrected | | | Monochrome | BIOS from | | | | System Soft, | | | | Inc.; see | | | | Note 2. | +------------------+--------------+--------------+ | IBM Corporation | P/S NOTE | For OS/2 | | | 425, 425c | 2.11, use F1 | | | | to display | | | | the | | | | configuration| | | | panel and | | | | set Resume | | | | on Alarm to | | | | OFF when | | | | running the | | | | Alarm | | | | applet. | +------------------+--------------+--------------+ | IBM Corporation | ThinkPad | Version 1.2 | | | 700, 700C, | of the | | | 720, 720C, | reference | | | 750 | and | | | | diagnostic | | | | diskettes | | | | are | | | | required. | +------------------+--------------+--------------+ | NCR Corporation | NCR(**) 3150 | BIOS | | | 486SX/25 | information | | | Active | displayed on | | | Matrix Color | start up: | | | | | | | | PhoenixBIOS|TM) A486 | | | Version 1.0| | | | (C)1989-199| | | | Phoenix Tec|nologies Ltd. | | | All Rights |eserved. | | | Reference I| 15 +------------------+--------------+--------------+ | NCR Corporation | SAFARI | Battery | | | | Life, Power | | | | Source, and | | | | Battery | | | | State | | | | information | | | | is | | | | incorrect. | +------------------+--------------+--------------+ | NEC Corporation | UltraLite | | | | Versa | | +------------------+--------------+--------------+ | Sharp | 6800 | Battery | | | | Life, Power | | | | Source, and | | | | Battery | | | | State | | | | information | | | | might be | | | | incorrect. | +------------------+--------------+--------------+ | Texas | TravelMate(**| | | Instruments, | 4000, | | | Inc. | 486DX2, | | | | 50MHz | | +------------------+--------------+--------------+ | Toshiba | T1950, | | | Corporation | T1950CS, | | | | T1950CT | | | | 486DX2/40 | | | | Mono, Dual | | | | Scan Color, | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T3400, | | | Corporation | T3400CT | | | | 486SX/33 | | | | Monochrome, | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T4700CS | | | Corporation | 486DX2/50 | | | | Dual Scan | | | | Color | | +------------------+--------------+--------------+ | Toshiba | T4700CT | | | Corporation | 486DX2/50 | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T6600C, | | | Corporation | T6600C/CD, | | | | T6600C/CDV | | | | 486DX2/66 | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Twinhead Corp. | SubNote | Does not | | | 486DX/33 | have the CPU | | | 486DX/33 | clock | | | Monochrome | slowdown | | | | feature; see | | | | Note 3. | +------------------+--------------+--------------+ | Zenith | MastersPort | | | Electronics | 386SLe | | | Corp. | | | +------------------+--------------+--------------+ | Zenith | ZNOTE 325L | | | Electronics | | | | Corp. | | | +------------------+--------------+--------------+ Note 1: To run OS/2 2.11 in these models, change the "BASEDEV=IBM1S506.ADD" statement in CONFIG.SYS to the following: BASEDEV=IBMINT13.I13 Note 2: For these models, the following BIOS information is displayed on start up: Systems Soft Bios for 80486/82C463 v1.01 (2069-09) Contact Systems Soft, Inc. (508-651-0088) for a corrected version of BIOS. Note 3: The OS/2 APM calls the BIOS APM once per second to check if it is OK to do a suspend. The following BIOS do not return OK to suspend if the video display is active or changes during the CMOS suspend timeout: o PhoenixBIOS Version 1.03 o Phoenix NoteBIOS 486/OPTi463 Version 1.03 o PhoenixMISER V2.0 Laptop Computers without APM Support The table that follows lists the laptop computers that do not have APM support in their BIOS; however, they can be configured to run OS/2 2.11 if APM is not installed. (This list represents only systems tested as of January 27, 1994.) If you have installed OS/2 APM, ensure that it is removed properly by doing the following: o Remove the following two APM device statements from CONFIG.SYS: DEVICE=C:\OS2\APM.SYS DEVICE=C:\OS2\MDOS\VAPM.SYS o Delete the APM.SYS and VAPM.SYS files from the corresponding hard-disk subdirectories. This gains about 1 second in startup and frees up hard-disk space. +------------------+--------------+--------------+ | Manufacturer | Model | Comments | +------------------+--------------+--------------+ | Compaq Computer | LTE-386s/25 | See Note 1. | | Corp. | | | +------------------+--------------+--------------+ | Compaq Computer | LTE LITE | See Note 1. | | Corp. | 25/c 386SL | | +------------------+--------------+--------------+ | Compaq Computer | LTE LITE | See Note 1. | | Corp. | 4/25e, | | | | 4/25c, | | | | 486SL/25 | | | | Active | | | | Matrix | | +------------------+--------------+--------------+ | Compudyne | 3SXL/25 | BIOS | | | SLIMNOTE | information | | | | displayed on | | | | start up: | | | | | | | | PhoenixBIOS|TM) for | | | VLSI Laptop|80386 BIOS | | | Version 1.0| R2-1 06/09/92 +------------------+--------------+--------------+ | IBM Corporation | L40SX | Discontinued | | | | product. | | | | See Note 2. | +------------------+--------------+--------------+ | IBM Corporation | P/S NOTE, | For OS/2 | | | Model 2141 | 2.11, use F1 | | | | to get the | | | | configuration| | | | panel and | | | | set Resume | | | | on Ring and | | | | Resume on | | | | Alarm to | | | | OFF. | +------------------+--------------+--------------+ | IBM Corporation | PS/2 N51 | Install | | | 386SX/SLC | using | | | 8551-025 | UINSTALL. | +------------------+--------------+--------------+ | Librex | T386SX | If screen is | | | | black after | | | | resume, | | | | toggle the | | | | F1 key | | | | (Suspend | | | | key) to | | | | refresh | | | | screen. | +------------------+--------------+--------------+ | Northgate | ZX Portable | BIOS | | Computer Systems | 486SX/25 | information | | | | displayed on | | | | start up: | | | | | | | | Phoenix A48| version 1.01 | | | | | | | See Note 3. | +------------------+--------------+--------------+ | Texas | TravelMate | See Note 3. | | Instruments, | 4000 WinDX2, | | | Inc. | 486DX/25 MHz | | +------------------+--------------+--------------+ | Texas | TravelMate | See Note 3. | | Instruments, | 4000 | | | Inc. | WinSX(**) | | +------------------+--------------+--------------+ | Texas | TravelMate | See Note 3. | | Instruments, | 4000e SX25 | | | Inc. | Passive | | | | Matrix Color | | +------------------+--------------+--------------+ | Texas | TravelMate | See Note 3. | | Instruments, | 4000e | | | Inc. | WinDX2/50 | | | | Active Color | | +------------------+--------------+--------------+ | Texas | TravelMate | See Note 3. | | Instruments, | 4000 | | | Inc. | WinDX2/50 | | | | 486DX2/50 | | | | Monochrome | | +------------------+--------------+--------------+ | Toshiba | T1800 | See Note 4. | | Corporation | 386SX/20 | | | | Monochrome | | +------------------+--------------+--------------+ | Toshiba | T1850, | See Note 4. | | Corporation | T1850C | | | | 386SX/25 | | | | Monochrome, | | | | Dual Scan | | | | Color | | +------------------+--------------+--------------+ | Toshiba | T1900, | See Note 4. | | Corporation | T1900C | | | | 486SX/20 | | | | Monochrome, | | | | Dual Scan | | | | color | | +------------------+--------------+--------------+ | Toshiba | T2200SX | See Note 4. | | Corporation | 386SX/20 | | | | Monochrome | | +------------------+--------------+--------------+ | Toshiba | T3100SX | See Note 4. | | Corporation | 386SX/16 | | | | Mono Plasma | | +------------------+--------------+--------------+ | Toshiba | T3300SL | See Note 5. | | Corporation | 386SL/20 | | | | Monochrome | | +------------------+--------------+--------------+ | Toshiba | T4400SX, | See Note 4. | | Corporation | T4400SXP, | | | | T4400SXC | | | | 486SX/25 | | | | Mono, | | | | Plasma, | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T4400C | See Note 4. | | Corporation | 486DX/33 | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T4500, | See Note 4. | | Corporation | T4500C | | | | 486SX/20 | | | | Monochrome, | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ | Toshiba | T4600, | See Note 5. | | Corporation | T4600C | | | | 486SL/33 | | | | Monochrome, | | | | Active | | | | Matrix Color | | +------------------+--------------+--------------+ Note 1: To run OS/2 2.11 in these models, change the "BASEDEV=IBM1S506.ADD" statement in CONFIG.SYS to the following: BASEDEV=IBMINT13.I13 Note 2: For OS/2 2.11 APM, access the IBM BBS and download the following 3 files: o TGSFX.COM (located in file area 4) o RFL40SXA.TG0 (located in file area 27) o L40PWR.ZIP (located in file area 37) --------------- (**) NCR is a trademark of the NCR Corporation. TravelMate is a trademark of Texas Instruments, Inc. (**) WinSX is a trademark of Texas Instruments, Inc. Execute TGSFX.COM to install the TELEGET.EXE program. Then do the following: 1. Create a new L40SX reference diskette by using TELEGET.EXE to unpack RFL40SXA.TG0 onto a 1.44MB formatted diskette. 2. Use PKUNZIP to unzip the L40PWR.ZIP to obtain new IDLE.EXE and PWRMGMT.SYS files. 3. Replace the IDLE.EXE and PWRMGMT.SYS files on the newly created L40SX reference diskette with the new IDLE.EXE and PWRMGMT.SYS files obtained from the previous step. 4. Restart L40SX with the resulting reference diskette in A drive and configure with APM. 5. Verify the APM configuration by selecting VIEW configuration from the installation menu. 6. Exit the configuration. 7. Power off the computer and restart OS/2. Note 3: Contact the manufacturer for newer versions of their BIOS that have APM support. Note 4: These models require the Toshiba APM driver (OS2RES.EXE) available from the Toshiba BBS (714-837-4408). This driver will provide partial power management capabilities under OS/2 2.11. Note 5: While running OS/2, you can use the special power-saving keys but the additional capability of OS/2 protect-mode APM is not supported. APPENDIX B. ERROR MESSAGES ___________________________ > On page 422, replace the paragraph under Action: for the SYS0206E message with the following: Correct the file name or the extension; then retry the command. For more information about file names, refer to "types of files, description" in the Master Index. APPENDIX C. BACKING UP AND RESTORING YOUR DESKTOP __________________________________________________ > On page 431, replace the last note with the following: Note: The name of your DESKTOP directory might be slightly different if you use HPFS or if you previously replaced your desktop. To find the actual name of your DESKTOP directory currently in use, display the Settings notebook for the desktop and select the File page. The current desktop name is shown under Physical name. > On page 431, replace the last line with the following: BACKUP C:\OS2\DESKTOP A: /S > On page 433, replace lines #10, #11, and #12 with the following instructions: 10. Delete the existing desktop directory and its subdirectories. 11. Use the RESTORE command to copy the DESKTOP directory and its subdirectories from the diskette to the hard drive. RESTORE A: C:\OS2\DESKTOP /S This will ensure that the desktop folders are displayed correctly. 12. Remove the diskette from drive A. 13. Press Ctrl+Alt+Del to restart the computer. APPENDIX F. REMOVING PROGRAMS ______________________________ > On page 453, replace the bit-map paths with the following: \OS2\BITMAP\BLOCKS.BMP \OS2\BITMAP\BOX.BMP \OS2\BITMAP\BRICK.BMP \OS2\BITMAP\BUTTERFL.BMP \OS2\BITMAP\COLUMNS.BMP \OS2\BITMAP\DELFT.BMP \OS2\BITMAP\FLAMINGO.BMP \OS2\BITMAP\FLEUR.BMP \OS2\BITMAP\LEAVES.BMP \OS2\BITMAP\LINES.BMP \OS2\BITMAP\LINKS.BMP \OS2\BITMAP\MAZE.BMP \OS2\BITMAP\MERCADO.BMP \OS2\BITMAP\ORCHIDS.BMP \OS2\BITMAP\ROOF.BMP \OS2\BITMAP\SCALES1.BMP \OS2\BITMAP\SCALES2.BMP \OS2\BITMAP\SHELL.BMP \OS2\BITMAP\SPIRAL.BMP \OS2\BITMAP\STARS.BMP \OS2\BITMAP\TILE.BMP \OS2\BITMAP\TOOTH.BMP \OS2\BITMAP\WAVE.BMP \OS2\BITMAP\WEBB.BMP \OS2\BITMAP\ZIGZAG.BMP > On page 455, replace the RIPL .HLP path with the following: \OS2\INSTALL\RIPLINST.HLP > On page 455, replace the TUTORIAL.HLP path with the following: \OS2\HELP\TUTORIAL\TUTORIAL.HLP > On page 456, replace the KLONBGA.DLL path with the following: \OS2\APPS\DLL\KLONBGA.DLL > On page 456, replace the NEKO.DLL path with the following: \OS2\APPS\DLL\NEKO.DLL > On page 458, replace the PMSEEK.DLL path with the following: \OS2\APPS\DLL\PMSEEK.DLL > On page 458, replace the .DLL paths for Scramble with the following: \OS2\APPS\DLL\SCRAMBLE.DLL \OS2\APPS\DLL\SCRCATS.DLL \OS2\APPS\DLL\SCRLOGO.DLL > Starting on page 458, replace the .DLL paths for SoftTerm with the following: \OS2\APPS\DLL\CTLSACDI.DLL \OS2\APPS\DLL\OACDISIO.DLL \OS2\APPS\DLL\OANSI.DLL \OS2\APPS\DLL\OANSI364.DLL \OS2\APPS\DLL\OCHAR.DLL \OS2\APPS\DLL\OCM.DLL \OS2\APPS\DLL\OCOLOR.DLL \OS2\APPS\DLL\OCSHELL.DLL \OS2\APPS\DLL\ODBM.DLL \OS2\APPS\DLL\OFMTC.DLL \OS2\APPS\DLL\OIBM1X.DLL \OS2\APPS\DLL\OIBM2X.DLL \OS2\APPS\DLL\OKB.DLL \OS2\APPS\DLL\OKBC.DLL \OS2\APPS\DLL\OKERMIT.DLL \OS2\APPS\DLL\OLPTIO.DLL \OS2\APPS\DLL\OMCT.DLL \OS2\APPS\DLL\OMRKCPY.DLL \OS2\APPS\DLL\OPCF.DLL \OS2\APPS\DLL\OPM.DLL \OS2\APPS\DLL\OPROFILE.DLL \OS2\APPS\DLL\ORSHELL.DLL \OS2\APPS\DLL\OSCH.DLL \OS2\APPS\DLL\OSIO.DLL \OS2\APPS\DLL\OSOFT.DLL \OS2\APPS\DLL\OTEK.DLL \OS2\APPS\DLL\OTTY.DLL \OS2\APPS\DLL\OVIO.DLL \OS2\APPS\DLL\OVM.DLL \OS2\APPS\DLL\OVT.DLL \OS2\APPS\DLL\OXMODEM.DLL \OS2\APPS\DLL\OXRM.DLL \OS2\APPS\DLL\SACDI.DLL \OS2\APPS\DLL\SAREXEC.DLL Appendix A. Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only IBM's product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of IBM's intellectual property rights or other legally protectable rights may be used instead of the IBM product, program, or service. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by IBM, are the user's responsibility. IBM may have patents or pending patent applications covering subject matter in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to the IBM Director of Licensing, IBM Corporation, 208 Harbor Drive, Stamford, Connecticut 06904-2501, USA. TRADEMARKS AND SERVICE MARKS ____________________________ The following terms, denoted by an asterisk (*) in this publication, are trademarks or service marks of the IBM Corporation in the United States or other countries: AT IBM Micro Channel OS/2 PS/1 PS/2 ThinkPad Ultimotion WIN-OS/2 XGA The following terms, denoted by a double asterisk (**) in this publication, are trademarks of other companies as follows: Trademark Owner Adaptec Adaptec, Inc. Allways Funk Software, Inc. AMI American Megatrends, Inc. ATI ATI Technologies, Inc. Central Point Central Point Software, Inc. Compaq Compaq Computer Corporation CorelDraw Corel Systems Corporation Docking Station NEC Home Electronics, Inc. Future Domain Future Domain Corporation Gateway Gateway Systems Corporation Gateway 2000 Gateway 2000, Inc. Hitachi Hitachi Ltd. HYPERACE Hypertec Pty. Limited Lexmark Lexmark International, Inc. McAfee McAfee Associates. Media Vision Media Vision, Inc. Micropolis Micropolis Corporation Microsoft Microsoft Corporation Mitsumi Mitsumi Denki Kabushki Kaisha MS Microsoft Corporation MS-DOS Microsoft Corporation NCR NCR Corporation NetWare Novell, Inc. Nomad Gateway 2000, Inc. Panasonic Matsushita Electric Industrial Co., Ltd. PCMCIA Personal Computer Memory Card International Association Phoenix Phoenix Technologies, Ltd. ProAudio Spectrum Media Vision, Inc. ProComm Datastorm Technologies, Inc. Quantum Quantum Corporation Sony Sony Corporation Sound Blaster Creative Labs, Inc. The Norton Antivirus Symantec Corporation TravelMate Texas Instruments, Inc. Ultra ATI Technologies, Inc. VESA Video Electronics Standards Association Windows Microsoft Corporation WinSX Texas Instruments, Inc.