THENET X1-J4 QUICK REFERENCE GUIDE ================================================================== SWITCH COMMANDS ACL [{CALLSIGN + VALUE} | {CALLSIGN - VALUE} | { * VALUE } | { & value }] ADC ADC1 [ * | Units_for_Voltmeter_channel_1 ] (see note 6) ADC2 [ * | Units_for_voltmeter_channel_2 ] (see note 6) ADC3 [ * | Units_for_Voltmeter_channel_3 ] (see note 6) ADC4 [ * | Units_for_voltmeter_channel_4 ] (see note 6) ALIAS [ * | NEW_ALIAS ] ARP [ipaddr [{ - ptcl } | [+ [P] ptcl callsign [DG | VC ]]] ARPTIMER [ * | enable_flag [ * | timer_rate ] ] AUDIT [ NUMBER_FROM_0_TO_255 ] BBS [ CALLSIGN | * | ? ] BBSALIAS [ * | NEW_ALIAS ] BRATE [ * | radio_brate [ * | rs232_baud_rate ]] (PK96 only ) BTEXT [ * | BEACON_MESSAGE_TEXT ] (see note 6) BYE CALIBRATE [PERIOD_VALUE_FROM_1_TO_60 [TOGGLE_VALUE_1_TO_PERIOD ] ] CLOSEDOWN A CONNECT [ CALLSIGN [ [V] DIGILIST ... ] CQ [ MESSAGE_FOR_CQ_PACKET ] CTEXT [ * | CONNECT_MESSAGE_TEXT ] (see note 6) DXCLUSTER [ CALLSIGN | * | ? ] DXCALIAS [ * | NEW_ALIAS ] HELP HOST [ CALLSIGN | * | ? ] HOSTALIAS [ * | NEW_ALIAS ] INFO [ SYSOP_SET_MESSAGE ] (see note 6) IPADDRESS [ NEW_IP_ADDRESS ] IPBROADCAST [ NEW_IP_ADDRESS ] IPROUTE [ipaddr [/bits ] [ - | { + port [ipgateway[metric ]]]] IPSTATS [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5) L3MHEARD [ NUMBER_FROM_1_TO_100 ] LINKS MANAGER METER [ { new_value | * } ... ] (see note 5) MHEARD [ NUMBER_FROM_1_TO_100 ] MODE [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5) MTU [ list_of_parameters ] (see note 5) NODES [* [*] | NODECALL {+|-} IDENT QUAL COUNT PORT NEIGHBOUR [DIGIS]] PARMS [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5) QUIT RESET [ ANY_CHARACTER ] ROUTES [ PORT NODECALL [ DIGILIST ... ] { + | - } PATHQUALITY ] STATS SYSOP TALK [ STRING ] UI DEST STRING_OF_TEXT_TO_BE_SENT_IN_UI_FRAME USERS ------------------------------------------------------------------ Note 1 Any command may be enabled or disabled by the use of the '+' or '-' modifier, as shown below : ANY_COMMAND [ + | - | THAT_COMMANDS_PARAMETERS ] Commands may be caused to be displayed or not in the prompt screen if the '-' or '+' is followed by 'D' ( or 'd' ) Note 2 IP addresses are of the form nnn.nnn.nnn.nnn where nnn is a number 0..255 Note 3 IProute port parameter is 0 for radio or 1 for rs232 Note 4 ARP ptcl parameter is AX.25 or Net/Rom (may be abbreviated) Note 5 The commands will accept the 'old' syntax of '* * * value...' or the new offset & value syntax of '/ parameter_number value' Note 6 Voltmeter channels 1,2,3,4 correspond to ADC channels 3,4,1,2 respectively. The ADC command reads them. HOST 'ESCAPE' COMMANDS C D P [ NEW_PASSWORD ] ================================================================== UNDERSTANDING ACL VALUES UNDERSTANDING AUDIT BITS ------------------------------------------------------------------ Bit Function | Bit Function =================================|================================ 0 Bar all incoming L2 connects | 0 Issue L1 stats every 10 mins 1 Bar outgoing L2 downlinks | 1 Audit L2 connects & discs 2 Ignore nodes broadcasts | 2 unused 3 Bar gatewaying at level 3 | 3 Audit L4 connects & discs 4 Bar incoming L4 connects | 4 Audit L7 use of sysop cmd 5 Bar outgoing L4 connects | 5 Audit all L7 switch commands 6 ignore SSID in searching | 6 Issue CPU stats every 10mins 7 unused | 7 unused ================================================================== PARMS PARAMETERS Number Min Max Function ----------------------------------------------------------- 1 1 400 Maximum number of destination nodes 2 0 255 Minimum quality for auto update 3 0 255 HDLC ( radio, port 0 ) default quality 4 0 255 RS232 ( crosslink, port 1 ) default quality 5 0 255 Initial value for obsolescence counter 6 1 255 Minimum obsolescence for node broadcast 7 0 65535 Auto update broadcast interval (seconds) 8 0 255 Level 3 ( network ) Time To Live Initialiser 9 5 600 Level 4 ( transport ) timeout (seconds) 10 1 127 Level 4 ( transport ) retries 11 1 60 Level 4 ( transport ) ack delay (seconds) 12 1 1000 Level 4 ( transport ) busy delay (seconds) 13 1 127 Level 4 ( transport ) window size (frames) 14 1 127 Level 4 ( transport ) congestion ctrl threshold 15 0 65535 Level 7 ( switch ) inactivity timeout (seconds) 16 0 255 Persistance for transmit delay 17 0 127 Persistance slottime delay (10's of msecs) 18 1 15 Level 2 ( link ) T1 timeout, ie FRACK (seconds) 19 1 7 Level 2 ( link ) window size (packets) 20 0 127 Level 2 ( link ) retries 21 0 6000 Level 2 ( link ) T2 timeout (10's of msecs) 22 0 65535 Level 2 ( link ) T3 timeout (10's of msecs) 23 0 1 Level 2 ( link ) digipeat enable flag 24 0 1 Callsign validation flag 25 0 2 Node beacon ctrl (0=off, 1=if active, 2=always) 26 0 1 CQ broadcasts enable flag ================================================================== MODE PARAMETERS Number Min Max Function ----------------------------------------------------------- 1 0 1 Hardware handshake host control mode flag 2 0 3600 CWID repeat period ( seconds ) 3 4 10 CWID speed ( 10's msecs per dot ) 4 0 3 Nodes broadcast channel enable flags where 0=none, 1=HDLC only, 2=RS232 only, 3=Both ports 5 0 3 Crosslink protocol selection 0=crosslink, 1=KISS, 2=KISS+selective copy, 3=KISS+allcopy 6 0 255 TX keyup delay ( 10's of milliseconds ) 7 0 1 Full duplex enable flag 8 0 65535 RS232 ( port 1 ) node broadcast period ( secs ) 9 0 3 Node broadcast algorithm control flags 0=off, 2=RS232 port, 1 & 3 not normally used 10 600 3600 Beacon interval ( seconds ) 11 0 2 Connect redirection to BBS flag 12 0 255 Help messages flags, 8 bit TALK, case & TEXNET 13 0 3 Hash node broadcast disable (one bit per port) 14 0 1 Enable extra aliases monitoring if set 15 0 1 Enable auto reconnect to node after remote dis 16 0 3 Slime trail control. Each bit controls... Bit 0 if set hides slime trails in nodes list Bit 1 if set causes slime trails to be ignored 17 0 3 Digipeat control. Each bit controls ... Bit 0 set makes node to refuse digi'd L2 uplink Bit 1 set, node refuses to allow digi downlinks ================================================================== IPSTAT PARAMETERS Number Min Max Function ( Those marked '*' are not used ) ----------------------------------------------------------- 1 0 3 ip L2 AX.25 Modes ( 1 bit per port, 1=DG ) 2 0 1 ip Forwarding, 1=enable router, 0=disable 3 2 255 ip Default TTL 4 0 0 ip In Receives 5 0 0 ip In Header Errors 6 * 0 0 ip In Address Errors 7 0 0 ip Forwarded Datagrams 8 0 0 ip In Unknown Protocols 9 * 0 0 ip In Discards ( TTL exceeded ) 10 * 0 0 ip In Delivers 11 0 0 ip Output Requests 12 * 0 0 ip Output Discards 13 0 0 ip Output No Routes 14 * 1 30 ip Reasm Timeout 15 * 0 0 ip Reasm Requireds 16 * 0 0 ip Reasm OKs 17 * 0 0 ip Reasm Fails 18 0 0 ip Frag OKs 19 * 0 0 ip Frag Fails 20 0 0 ip Frag Creates ================================================================= MTU PARAMETERS Number Min Max Function ----------------------------------------------------------- 1 64 1024 IP Port 0 ( Radio Port ) Level 2 AX.25 MTU 2 64 1024 IP Port 1 ( RS232 Port ) Level 2 AX.25 MTU 3 64 236 IP Net/Rom port MTU 4 257 1025 Level 2 Max data bytes in a packet before error 5 328 1096 Level 2 Total max packet size in bytes ================================================================= METER PARAMETERS Number Min Max Function ----------------------------------------------------------- 1 0 511 The meter mode flags 2 0 255 The deviation meter scaling factor 3 0 255 The signal strength meter noise floor value 4 0 255 The S meter display format multiplier 5 0 255 The dBm meter display format multiplier 6 0 255 The dBm noise floor value 7 0 255 The voltmeter channel 1 multiplier 8 0 255 The voltmeter channel 2 multiplier 9 0 255 Voltmeter Channel 1 offset value 10 0 255 Voltmeter Channel 2 offset value 11 0 255 The voltmeter channel 3 multiplier 12 0 255 The voltmeter channel 4 multiplier 13 0 255 Voltmeter Channel 3 offset value 14 0 255 Voltmeter Channel 4 offset value ================================================================== THE METER MODE FLAGS ( METER parameter 1 ) BIT If set, then .... ----------------------------------------------------------- 0 The deviation meter is enabled 1 The signal strength meter is enabled 2 The signal strength is shown as S points rather than dBm 3 ADC channel 3 is enabled ( voltmeter channel 1 ) 4 ADC channel 4 is enabled ( voltmeter channel 2 ) 5 Voltmeter channel 1 divisor is 1000 rather than 100 6 Voltmeter channel 2 divisor is 1000 rather than 100 7 Voltmeter channel 1 display resolution is 0.1 not 1.0 8 Voltmeter channel 2 display resolution is 0.1 not 1.0 9 ADC channel 1 is enabled ( voltmeter channel 3 ) 10 ADC channel 2 is enabled ( voltmeter channel 4 ) 11 Voltmeter channel 3 divisor is 1000 rather than 100 12 Voltmeter channel 4 divisor is 1000 rather than 100 13 Voltmeter channel 3 display resolution is 0.1 not 1.0 14 Voltmeter channel 4 display resolution is 0.1 not 1.0 ================================================================== HELP MESSAGES FLAGS ( MODE Parameter 12 ) BIT FUNCTION ----------------------------------------------------------- 0 If set, the 'please wait, trying xxxx' operates 1 If set, all commands appear in help for sysop 2 If set, the 'goodbye' message is given 3 If set, a welcome message is enabled ( CTEXT ) 4 If set, nodes are shown as 'alias:callsign' 5 If set, TALK data is passed as 8 bit data 6 If set, node aliases are deemed to be case sensitive 7 If set, enables the TexNet "*** LINKED to" interface ================================================================= ARPTIMER PARAMETERS Number Min Max Function ----------------------------------------------------------- 1 0 1 0 disables ARP table mgmt, 1 enables 2 15 1440 ARP entry expiry time in minutes